after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I want to make a connectable bluettoth transmission. I need 1 service with 3 characteristics, but for now I only want to see my service in app. It is possible to do it...
I have a nRF24LE1 processor.
We have an 'RF bootloader' which operates from the pc running a 'nRFUpdate 'Firmware over the air'' program using a dongle made by 'sparkfun...
i am running this code on my nrf.
const nrf_drv_timer_t TIMER_LED = NRF_DRV_TIMER_INSTANCE(0);
uint8_t flag;
/**
* @brief Handler for timer events.
*/
void...
I currently have both the nRF51 DK and nRF51 Dongle plugged on my PC. In Keil, when I try to load my program into the nRF51 DK I get the following error: "No JLink is selected...
HI People,
I face a problem when I do an OTA DFU from APP to APP. I compiled ble_app_hrs S110_with_dfu example fro sdk 9.0.0 and did OTA dfu. Now the device advertises...
I'm in the middle of putting a NRF51822 device through bluetooth certification. The test house has asked that I have modes where the radio is transmitting on certain frequencies...
Hello. I finally succeeded mouse keyboard combo. I use mouse sensor with SPI. I send mouse_move_data in loop. However, when I connect with the computer, the mouse pointer...
I am trying to debug a SPI application using Keil and the Eval board, but am having problems with control of the port pins. I am using pin 23 as the CS pin. it configures...
On SDK 9.0 only
Do not judge the quality of SDK based on number of entries here. This thread should be considered part of Nordic effort to main the quality of the release...
Hi,
I'm in the process of transitioning my application and associated bootloader from SDK 7.2.0 to SDK 9.0.0.
I can compile both my application and bootloader now against...
Hello,
In order to test my BLE project with a development kit from Nordic, i want to know the following :
Does the nRF51-DK contains Revision 3 of the nRF51422 ?
...
I just bought the nRF51 DK and trying to follow the Beacon Transmitter Sample Application Example.
I would have 2 questions:
1 - At one point it says "Define the compiler...
I use SDK 8 or 9 &my compiler Keil uVision 5
my Development kit pca10028
Where should I add thede #include files?
I Mean de XXXX.h or de XXX.c.
Where Should I add de...
Hello, I've searched the forum for information regarding handling real-time tasks with the nrf51822. I've found this post -- devzone.nordicsemi.com/.../ -- which is similar...
