Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am having trouble getting the data (7 ASCII characters) transmitted via UART using the interrupt driven mode. The uart_fifo_fill function returns a positive number (the...
Hello,
I was developing an application and was using the ble glucose application as a template. This uses the s140 softdevice, however as I am using the nRF52811 in peripheral...
Hi,
As queried before in this link , I am not able to restore the model publication state after reboot. Am using sensor server example to write my application on top of...
Hi,
Because I am not getting any answers to my original ticket(ID: 294922), I'll try it this way by opening another ticket on the same issue.
I have a nrf9160DK and flashed...
Kind folks,
Situation: The product page for the Thread Topology Monitor v1.3.0 lists the following compatible dev kits (to which I've added the PCA numbers):
nRF52840...
Hi, is it posibile for use nrf21540 in the other brand BLE MCU board? some custmer maybe do not want use Nordic BLE, but want use nrf21540+other brand BLE, it is posible to...
hello!
I want to use Jlink to download code to a NRF52840 chip as MCU development board, but the number of pins and pin spacing of my Jlink are different from it. So I had...
Hi, Nordic support,
I have built success with the example "nrf5340_audio" set the gateway mode. when I run the example into my board "NRF5340 Audio DK" I get this error...
Hi,
I'm trying to use the nRF9160-DK(Ver.1.0.0) for LTE communication and GPS location information acquisition.
I found a list of LTE antennas at this URL. However, I...
We are using NRF5 SDK 17.0.2 on an NRF52840.
I am implementing a bootloader update procedure. Our updates always store the new image in external flash. The spare space in...
Hi,
I'm interested in using this AT command to upgrade my nRF52840. But I'm not quite sure what to do exactly. I'm using nRF5 V17 SDK on nRF52840. what should I provide...
Hello,
I'm thinking of increasing the transmit strength of my peripheral device using the function provided below.
sd_ble_gap_tx_power_set(BLE_GAP_TX_POWER_ROLE_ADV ,...
HI,
We are working on nRF5340DK need testing procedure for direction finding (AOA, AOD). So far we have tried to Download and install nRF connect Application for Mobile...
HI,
We are working on nRF5340DK need testing procedure for direction finding (AOA, AOD). So far we have tried to Download and install nRF connect Application for Mobile...
