If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi,
I'm trying to build a proof of concept for a BLE gateway that captures data from BLE sensors and sends it to the cloud via LTE-M connection. I'm hoping that the gateway...
problem description:
hi, I just got a PCA10040 development board with which I plan to learn about nrf connect SDK.
so I try the common BLE peripheral demo,but I 've met...
In order to add the BLE DFU service, I need to increase the GATT table size and therefore memory as mentioned here: .
However, when I tried to increase the file ble_app_uart_gcc_nrf52...
Try by changing the RAM size but it didn't worked.
<info> app_timer: RTC: initialized. <error> app: ERROR 4 [NRF_ERROR_NO_MEM] at :0 PC at: 0x00000000 <error> app: End of...
Hello, I have managed to get two NRF5340DK linked and measured their throughput. Now I need to change their Output Radio Amplifier Power to test again. And then I also need...
Hello Nordic Team,
I have an issue on one of my 10056 DK. The DK is connected to a development PC, appears in device manager as a Jlink CDC UART port, and as a mass storage...
In the Zigbee framework, what is the purpose of the return variable from zb_osif_sleep() ? The "documentation" for Zigbee seems to implement a "guess and figure it out for...
Hi,
I'm following the ble_template example on my custom board. I'm having an issue with waking up (soft reset) the device from sd_power_system_off. I can power off the system...
Hi ,
We are using s140_nrf52_6.0.0_softdevice, SDK 15.0.0 for NRF52840 chip. Does this sdk and soft device supports extended advertisement?
I could able to enable this...
I use both nrf52833 boards to do AOA test.But i use thr antenna array board of silab.The board are 16 antennas.I use the NCS version 1.9.1.
The next is my device stcture...
Hey All:
I'm trying to create a new app in VS Code. I've got the latest v2.0.0 SDK. I get the following error:
[west]: FATAL ERROR: Malformed manifest file: /home/ebolton...
hi support team,
customer have one question about nrf dfu with serial:" how to disable flow control for 2 wire uart".
previously we have one ticket :"https://devzone.nordicsemi...
Hi,
I'm using nrf52832 DK with SPI slave mode to read 600 bytes from other nrf52832 DK with SPI master mode but i can't receive more than 255 bytes buffer.
If you know...
Hi everyone,
My project consists on a nrf5340dk working as a peripheal UART, i set the advertisment to coded phy like this:
Setting the child image as hr_coded for be...
Hi,
I want to buy a nRF5340-DK.
This is the image of the official Nordic web page https://www.nordicsemi.com/Products/Development-hardware/nrf5340-dk
It appears that...
