I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
I want to creat a hci vendor-specific command of zephyr using nRF connect SDK, based on hci_pwr_ctrl bluetooth sample.
At first, I think just using follow steps in hci_vs...
Hi,
Recently I have heard that there are license restrictions on using DKs for production programming. Is this only for production programming? Can I still use the DK to...
Hello, im trying to implement the UARTE Driver for simultaneous Use of Bluetooth and asynchrounos Uart TX/RX on a nRF52840 and nrf9160. The Problem is that neither RX or TX...
Hi
i want use a nRF52840Dongle as a Zigbee end device, when power up, i get following message:
I: nRF5 802154 radio initialized ***** delaying boot 5000ms (per build configuration...
Hi, I have just started evaluating nRF52840 using the dongle and Development Kit. I have successfully tested the Openthread network using CLI project. Now I want to try out...
Hi experts, The situation is following, the NRF53 shall receive multiple packets. After the reception of one of the packets the next one shall be received at the same frequency...
Hello,
I am struggling to commission a light bulb matter sample device (nrf52840dk) with the CHIP tool running on my Linux laptop. I set up an OpenThread Border Router with...
I had configured zephyr.dts file for UART and I2C pheripherals. And when I tried to build an application it is giving below error
Board : nrf5340 Application name : SHT...
I implemented the nRF52840 (auto)upgrade with an nRF9160 on the nRF9160DK. I did my development with the Serial Modem LTE application from nRF Connect SDK 2.0.0. I noticed...
Hey All:
I'm trying to install V2.0.0 of the NRF Connect SDK on a fresh Ubuntu 22.04 VM, and the whole thing seems broken.
Here's my steps:
install the nRF command...
Hi, I have found several aged topics on Devzone but need this feature and would like current state. If it still not supported, is there any example implementation on how manage...
Is there a way to rebuild (clean and build) a project in Visual Studio Code with the nRF Connect Extension? A web search shows how to do it with the CMake Extension ( https...
I am using the Connect SDK v2.0.0 and attempting to use TCP in the stock CLI example to mimic the demo shown here . When I flash the v2.0.0 CLI sample on my nRF52840dk, "...
Hi everyone,
I have some devices that are communicated through RS485. nRF52840 DK supports RS485 communication?
Do you have suggestions of how should I connect those devices...
I have a custom board with 8 LED's and I use pwm API led_on(), led_off, led_blink() etc, to turn them on, set brightness and blink and everything works fine except one case...
