Hi guys,
I am new to Nordic and I am using the evaluation kit "pca10001".
I have managed to run the LED BUTTON example which was declared in application note "nAN-36...
Hi,
I am having problem with the bootloader function of s110 v7. I am able to download the s110 softdevice. My application code was recompile with v7 header files. Able...
I am new to this forum and have some questions that I could not find elsewhere. The questions are:
Website asks me for a product key if I try to download the S210 soft...
Hi,
I'm starting to implement DFU using IAR's ARM workbench. In the example project for ARM that comes with the nrf51_sdk_v5_2_0_39364 SDK there is a file called bootloader_util_arm...
Do I have to use external host MCU for nRF51422? What can the ARM Cortex processor inside SoC 51422 do and cannot do?
I want to create a mesh network with hundreds of ANT...
Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
i m using nrf5340 cutom board, so i m using rtt logging method using jliink rtt viewer , to see logs .
so, when i am going to project section at top in embedded segger studio...
Hi,
I have a custom board with nRF52840/SDK 16/Softdevice 7.3.0 using Secure Dfu Bootloader. On my Android device I use Nordic Dfu Library. I have tried all available Dfu...
Ever since the toolchain manager v1.0.0 came out in the nRF Connect software, I have been unable to download it. I keep getting this error:
Any ideas?
Thanks,
Jow...
Hi
I am using SDK 1.9.1 with VS Code on MacOS to develop for nrf5340. I also have a nrf5340-DK board.
I am having problems finding the right includ file for using the...
I'm new at this (so be gentle). Trying to understand the process for activating a SIM card with Verizon using the NRF9160. I see that this modem is approved; so do I only...
Hi, I want to add CLI in our current firmware. i found a way to do is Zephyr shell. our firmware is based on aws iot sample and nrfconnet sdk1.9.0 after integrating zephyr...
According to data sheet of nRF52832, internal pull up resistance is 13kohm. Can we find the 13kohm internal pull up resistance in the code and can we change that internal...
Ideally we should not get any data when internal pull up resistors of nRF52832 board are disabled and external pull up resistors of SHT 40 Slave sensor are disabled. But I...
Hi,
I haven't been able to actually find out if the VBUS can be used to drive the DETECT signal to go from system off to on mode.
Are there any examples on how to configure...
Hello All, We have designed a custom board for our product and everything pretty much works fine. But now that we have decided to stick to WebBLE, we are facing some issues...
Hi,
I would like to declare my pin in output open-drain, so i use this configuration
My issue is when i declare my pin, I have an unexpected low state that occur...
Hi, I am currently getting started with the Thingy: 91 and am having trouble getting the SDK setup.
I download the file from: https://www.nordicsemi.com/-/media/Software...
1) Our device uses NRF52832 to connect with Android 7 system，use wireshark to monitoring，find not hop，is OK？ and wireshark delta time is Connection Interval ?
2) nrf52832...
Hello,
I need to use Port 1 pin 8 as an interrupt pin:
This results in the error NRF_ERROR_INVALID_STATE, when nrf_drv_gpiote_in_init() is called. Everything works fine...
Hi,
I want to monitor the connection state of my device as I have observed situations in which the callback functions defined with bt_conn_cb_register is not fired, causing...
