Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hi,
I'm trying to find an example of using the I2S audio interface with the Zephyr RTOS on the nRF52840dk_nRF52840 development board or on an nRF52840 device in general...
Hello ! I'm a beginner here, and I have a problem that I struggle to solve. A few years ago, a firmware was done by a company, for the one I work for. It was done with IAR...
Hi,
I am toggling a GPIO using the below code and trying to find out the relation of the frequency and the code statements. I know that GPIO peripheral is running at 16MHz...
Hi,
after fixing a missing ground in my setup (see devzone.nordicsemi.com/.../interaction-jlink-and-power-profiler-ppkii) I have not been able to get less than 50uA of idle...
My B0n bootloader (running on the network core) is trying to access XIP space and faulting. This is a part of an network core upgrade.
From what I can learn from the data...
Good evening,
I’m testing the SDK v17.1.0 “Open Bootloader with DFU” example. I’m using Segger Embedded Studio to program my Nano 33 BLE via the debug interface (P20) of...
Hello again Nordic World!
Yet another question about getting RSSI values:
Again, using 10028 and 10040 boards under sdk 12.3.
Is the adc acquisition of rssi done synchronously...
Dear DevZone,
within out project we make use of an esb communication between a nrf52840 DK connected to the PC via USB (a "station"), and a custom PCB with a nrf52840 micro...
Hi all,
We are developing an application using nRF52840 device and the idea is to enable the device with peripheral and central roles.
We would like to set two advertising...
Hi there,
We've been doing OTA DFU updates for a while now, but a recent increase (by one page = 4kb) of the firmware has created an issue.
Flashing through USB serial...
Hello,
I am using nrf9160 development kit. I need to use this dk with Modbus RTU master slave project. My question is does nrf9160 support for work on Modbus RTU master...
Hi Nordic,
I've reviewed the Mesh PyACI which uses a serial connection with a DK to provision a separate Mesh device over-the-air, if I understand correctly. But is there...
According https://www.nordicsemi.com/Products/Development-hardware/Nordic-Thingy-91/Download#infotabs
Version 1.2.7 seem to be the latest without "only for testing and development...
Hello,
I'm making an own service with a notify.
When I look at the bas service there is the following line to trigger the notifty:
Because I have serveral characteristics...
