Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
Hi
I try to run a nRF9160 on a nRF9160DK with lowest power possible.
A wake up from pin and periodically from RTC is required.
In the nRF9160_PS_v2.0.pdf is IMCUON1...
Hello,
We have a Xamarin Forms application, which we use for connecting to nrf52840 device and read/write characteristics. We managed to do it using Plugin.BLE nuget available...
I have difficulties in decoding the nRF9160 GPS output data. I know that nRF9160 reports its GPS data in NMEA GPGGA format, however, I am wondering why the last number which...
I want a waveform as below for motor control. I am trying to create this using nrf pwm driver.
I set the pwm sequence as below and checked the output. 2nd duty repeat does...
Hi,
I am trying to retrieve data from server using HTTP GET request, using AT command for Serial LTE modem application.
So, I can connect to the server using AT#XHTTPCCON...
I have a hardware like the PINE Watch, with nRF52832 and external memory XT25F32B connected via SPI with the following:
PIN P0.2 SCK
P0.3 MOSI
P0.4 MISO
P0.5 CS
...
I am developing my own low level radio protocol based on BLE advertisement telegrams with the nRF52840. It works good so far and the usage of SHORTS helps a lot.
But there...
Excuse me：
1、 I can't find the USB DFU example of the nrf52820 in the SDK.Does nrf52820 support USB DFU？
2、52820 needs to Implement USB OTA ，enumeration as keyboard...
Hello,
I'm trying to include a byte in the advertised data that indicates on which channel the advertisement is being sent, 0 = channel 37, 1 = channel 38, 2 = channel 39...
Hi,
We have a board with an nRF52840 working as the primary MCU which controls an nRF9160 via AT commands.
P109 from nRF52840 is connected to the nRESET of nRF9160. To...
Using the GPS sample application as a base, I examined the behavior of "concurrent" cellular and GNSS. I enabled cellular with at+cfun=21 after a GPS fix was obtained. I also...
Hello!
I'm currently working with Zephyr on a custom board based on the RAK5010 board. This board (RAK5010) is currently supported by the Zephyr project,uses the NRF52840...
Good day i am new to Nordics platform and SDK also new to segger embedded studio
i am required to develop a solution that receives data on the UART of the NRF52840(client...
Hi,
I have PCA63511 Power Profiling DK and nRF52840 DK ( and nRF9160-DK )
I was using SoftDevice SDK, and no issues with measuring nRF52840 device. But now I switched...
