Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi.
I am trying to get mesh DFU working and I keep getting "Failed to upgrade target. Error is: Crashed on start packet" from nrfutil.
When debugging the target I see...
I am using the nrf51822 ble with softdevice and want to know if the broadcast can start at a given time, and if the adv_ interval can change everytime? (such as I want to...
Hi Nordic Community,
I'm trying to run app timer in bootloader_secure. But when I add app_timer.c file to project, it built successfully but breaks when execute. I don't...
Hello,
I am using a custom nRF52840 ( SDK 14.2.0, SoftDevice S140) based board to connect with an iOS(v 13.3) phone.
I am sending data continuously over BLE. However I...
Hi,
I'm trying to find simple ADC code for one shot modus as described in the documentation: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.nrf52832...
I will use Nordic nrf52840 dongle for 2FA + security key on Google login and I am following these instructions:
https://github.com/google/OpenSK/blob/master/docs/install...
I use nRF52840 and SDK16 with S140 softdevice. I need 3 ADC ports. The initial code as follows.
static void adc_configure(void) { ret_code_t err_code = nrf_drv_saadc_init...
Hi,
I add a my .ilb file in the ses project .When I c all the function in the .lib file and build, it will have an log "undefined reference to 'xxxx'". But i can success...
I want to upgrade a BLE peripheral firmware (nrf52840) by using another nrf52840 as BLE central.
Do you have any idea how I can do that?
I know how to use android to upgrade...
Dk 0.8.5 with external GPS antenna modem FW: v1.1.1 nrf tag: v1.2.0 supl: v0.5.1 OS: Windows10
Put supl folder to "\ncs\nrf\ext\lib\bin\supl" * the path written in readme...
Hi,
I have a problem where I have to put a delay for 50 us after nrf_drv_rtc_counter_clear(&rtc); to get 0 counter from nrf_drv_rtc_counter_get(&rtc);
seems that the...
How to extract MQTT message from the Simple_MQTT sample for nrf9160-DK?
I am trying to use a specific message to trigger an action based on a predefined string. Not sure...
Hi,
As far as I understand, every connection establishment has to start with advertising.
Event if I have already connected and bonded to a peer, after disconnection...
Hi everyone,
I am using an nRF52840 dongle (MakerDiary) with SDK15.0 & SoftDevice S140 v6.0.0, and trying to change the BLE advertising manufacturer's data with the information...
