Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
i have a bunch of nrf51822 hwid 0024 or 001E.
With softdevice s110 version 7 everything worked fine, but starting with 8, they pretend to work fine (no error codes...
Using the pure-gcc makefiles, at present I only see this for a stack trace in the command line gdb client:
(gdb) bt
#0 0xfffffffe in ?? ()
#1 <signal handler called>...
If you have the most trivial main.c possible, with a main() which does nothing at all, compile, link and load it at 0x00000000, it runs fine and does nothing .. that's basically...
I have a nRF51822 program in which a button triggered event doesn't work as expected and crashes the program. The program may have potential race condition problem. Here is...
Hello,
I've overcome most of my problems using this wonderful Q&A system from other people. Recently I've moved from a nRF8001 + MCU to a nRF51
Using SDK 8.1.1, keil...
Hi all-
I apologize in advance for the noob question but I have spent loads of time on this and can't make progress. I am trying to work my way through the nrf51822 User...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Is it possible to add a payload (1-2 bytes) to the beacon advertising packet?
I intend place an ADC output to the payload. For now, I'm using nRF51-DK but later wants to...
Hello,
I'm developping an application using softdevice S130 with the nRF51822 evaluation kit.
The device has to scan multiple devices, and to save power, I'm storing the...
The SDK defines functions for operating on "ports", which are the output space divided into 8-bit chunks:
nrf_gpio_port_clear
nrf_gpio_port_dir_set
nrf_gpio_port_read...
As previously seen on softdevices topics ( devzone.nordicsemi.com/.../) I need to restrict BLE advertisement on only one channel for sniffing purpose.
The thing is, I cannot...
Bluetooth Smart Internet gateways (GATT)---Available early 2015 through the HTTP Proxy Service (HPS) & RESTful API white papers....
what does it mean..? is it available...
Hello,
I started to make an app for a board with nRF51822 with softdevice S120 version 1.0.1. Now I would like to have the DFU implementation in it but I am stuck at the...
