Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hey there! I'm looking for the official license info for nRF Command Line Tools and nRF Connect for Desktop. We want to install these on our work computers, but need to check...
Hello,
this is the first time I work with this device and the device is not for me or for my company.
I have to do an automatic test application, which should program...
Hi there,
So I am using an adapted version of the echo sample for I2S in the nRF Connect SDK in VS Code. I only want to use the echo example in receiving mode, so I have...
Hi, I'm using the nrf9160 with ncs2.7 on a custom board. Does the APN need to be explicilty set with `CONFIG_MODEM_ CELLULAR_APN` ? Or will it auto detect? Does it depend...
Hello,
We are using the NPM1300 with a lithium polymer battery that has integrated cell protection.
When the battery reaches the over-discharge level due to prolonged...
I got the following setup: nRF52840 - GenOnOffClient (Light Switch Sample) Publish to Group 0xC001
nRF52840 - GenOnOffClient (Light Switch Sample) Publish to Group 0xC001...
Hello!
I have a complex issue that I am trying to brainstorm. The task is that I am trying to receive a file over the air and be able to serial flash my STM32U575xx.
...
I have customed my own nrf54l15 board and run peripheral_uart demo successfully. Then I tried to measure its current while running peripheral_uart demo, it was up to almost...
Hi,
I've received the nRF54L15 DevKit and tested the power consumption during sleep Testproject in GIT: https://github.com/marcel-cd/nrf54l15dk-powertest
The result was...
Hi,
I am currently migrating from NCS 2.5.0 to 2.7.0 and running into an issue where the CMakeLists of mcuboot ( https://github.com/nrfconnect/sdk-mcuboot/blob/4c7942e58c5458ce3c4e50d3169e0f865910fe87...
Hi I use nRF52832 and nRF Connect SDK v2.6.1 with visual code
I went through this exercise ( academy.nordicsemi.com/.../) and the FOTA works so far. However, in this example...
Hi nordic:
I would like to inquire about the foundry, packaging, testing, ball-mounting, and process node (e.g. 28nm, 40nm, etc.) for the 52832 chip.
（Writing an internal...
Hello,
I am using VSC on Windows with nRF Connect. Previously I have installed the NCS SDK using the "RF Connect" Toolchain manager.
I have to make changes to some...
Hello,
I'm using my nRF52840 devkit together with nRF Connect for Desktop Bluetooth Low Energy (v4.0.4) app for some testing. The app failed to recognize my devkit. It used...
Hello .
I 'm studying Zephyr .
Is it possible to run a python program in the Zephyr environment ?
I am using Nordic 's nRF5340 SoC and I need certain modules in...
