I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi,
We're using nrf Connect SDK v2.4 and have issues when calling bt_gatt_notify() from our main thread. The bt_gatt_notify() function blocks even though we have the CONFIG_BT_L2CAP_TX_BUF_COUNT...
I merged two sensors, BME and BMI, and checked the raw data output through NRF_LOG_INFO. Now, I've added the new merged code to the main firmware, but the log for the BMI...
Hi there,
I have multiple flash partitions defined in pm_static.yml.
I want one specific partition to contain a binary data file so that when I flash the image with J...
Hi all,
I am developing a project with the nRF52840, using nRF Connect SDK 2.6.1 in Visual Studio Code.
I need to be able to compute an MD5 checksum for a dependency....
Hello, We have one of our products developed using the nrf52805 Module & nrf5 SDK . (which is already fully functional with our application ) Since we have few production...
Board : Nrf52480 custom board
IDE: VSCODE
NRF version : 2.6.99
Zephyr Version : 1.6.0
Segger systemview: 3.54
I followed the instruction from Zephyr RTOS, for using...
Hi support Team,
I would like to know the SDK version to be used for nRF54L15.
Is there any link to know details regarding the configuration, flashing and example codes...
I want to advertise a custom service so my central can filter for it and have a device name and manufacturer. I have the following code but can only seem to do either the...
Hi all,
I want for confirm my findings concerning ERASEUICR. I want to be able to erase the UICR from inside my firmware for automatic testing purposes (no debugger is...
I think I have a failing PPK2.
I tested it with this circuit.
My DVM shows the correct current flow - 1.48 mA. The PPK2 shows 40 micro Amps.
Note that the battery...
Hello,
Using nrf9131-ek because the nrf9161 doesn't seems to have the capability of using an external RC oscillator.
Plans are there in the project with using some/many...
Hello,
Using nrf9131-ek because the nrf9161 doesn't seems to have the capability of using an external RC oscillator.
Plans are there in the project with using some/many...
i have used this case:devzone.nordicsemi.com/.../using-swo-with-nrf52-redux and add ENABLE_SWO but when i flash and use jlink swo viewer,it will have this problem.
...
