Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hi
I need to send data from nRF7002 to external CPU(STM32) use UART protocol, for HW nRF7002 P0.20 connect STM32 RX and RF7002 P0.22 connect STM32 TX, I try to use exercise...
Hii,
i used nrf5sdk and i am trying to scanning i2c address of Sensirion sgp40 Sensor but unable to sacn i2c address.
I try SGP40 sensor with arduino code its work correctly...
I have tested NPM1300-EK with NRF52840DK and it works.
However, I am using other MCU with NPM1300 but it is a non -zephyr project.
To work with NPM1300, I have tried...
Hi,
I am using nRF7002 DK. I have set P1.04 as UART RX. For testing I am using TI CC26x2R1 Launchpad to send UART data to nRF7002 DK. I use a logic level shifter board to...
Hello,
I am currently trying to connect an external hardware codec and amp (Adafruit MAX98357 I2S Class-D Mono Amp) in order to play audio via BLE Audio and I2S using...
I have an NRF9161DK 1.0.0 , I was trying to do some wiring but the sensors didn't work, then I noticed that the board delivered 1.7v.
I tried changing it to 3.3v using the...
Hi,
My NRF52840DK ( pca10056 1.1.0 2019.9) would not reset when I press its Reset button. The issue is very similar to https://devzone.nordicsemi.com/f/nordic-q-a/38555...
I have new Thingy 53. Default Edge Inpulse demo works without any problem. But I have problem with Weather Station demo.
First I tested Zigbee version. After flashing using...
Hi,
What is the minimum LDO dropout voltage of nPM1300? For instance, in order to get 3.3V from the LDO, what is the minimum input for the LDO ? On the datasheet there is...
Dear all:
I have prepare env for border router successfully following this link( developer.nordicsemi.com/.../tools.html , Raspberry Pi4 and nRF52840( RCP: radio coprocessor...
I have a customer that wants to provide me with .a file for some confidential algorithm they want to run. I am tasked with implementing this into my firmware.
Using the...
I can't seem to get the FIFO to work and I think it is because I'm not dereferencing the consumer thread properly. I have reviewed the nRF Connect SDK Intermediate, data passing...
Hi,all
I need to connect BLE via NFC,but I do not know which example should i use to start。and i am a new field of NFC ,is there some document about NFC?thank you a lot...
