Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello! I'm currently working on a circuit design where weight and size are critical factors. Could you please tell me the minimum dimensions and weight of this chip? Thank...
I've made a new project as I had to change some hardware than the previous one.
The code seems fine, but I'm not able to load the libraries in the project.
A red underline...
When an ESD shock to the PCBA causes the nrf52840 to reboot, what reset code should we expect to show up with hwinfo_get_reset_cause()? RESET_BROWNOUT?
Using Zephyr NCS...
Hi! I am trying to use the LE Audio application and one of the samples in it, by including the necessary source files, and Kconfigs in my project. On the network core, I am...
As per the doc , when I use a smartphone (the base version is Android 12) to touch the NFC antenna, I should see a pop-up window:
3.Confirm pairing with ‘Nordic_HIDS_keyboard...
Is it possible to promote my project here: complete Zephyr development environment running solely on Raspberry Pi 4 Bookworm OS? If nothing else it does provide information...
Hi There,
During the transmission and reception performance test, I found that the LE1M's maximum sensitivity was only -92 dBm, while the LE2M's maximum sensitivity was...
Hi,
we have a Gateway board that uses the nRF52832 with the nRF21540.
The firmware running on the nRF52832 is a slightly modified version of the HCI UART sample found...
I have a problem with timer 3 of nrf52820.
It concerns a trailing edge dimmer implementation based on timer 3. A gpiote is used to sync the zero crossing.
I use ppi...
Dear Nordic-Team,
I designed a custom PCB using the nRF9151 as the host processor, the nRF7002 as a Wi-Fi companion, and the nPM1300 as the power management IC. The Wi-Fi...
Hello,
I encountered a strange behaviour on a nrf52832 : - I flash a a debug firmware (with debug optim in build config) : I can run debugger and add breakpoints - I stop...
I am developing an application that uses NCS2.8.0.
For FW updates, the nRF52833 USB ACM bootloader is enabled.
However, there are some problem.
My device has a battery...
Hi all hope you all are fine and doing well.
I am trying to use the Soft UART (uart-bitbang.c driver) on nRF52 DK for a low-speed UART connection. The initialization fails...
Hello, I am not sure if this is the most appropriate place to ask this question, but any comments are welcomed. I am developming a sensor platform that tries to use extended...
So hello everyone, I am a computer science student with zero IoT background. I am trying to a wearable device . I want to nrf52840DK with max30102 heart rate sensor and communicating...
