I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hello everyone. My task is to integrate eRPC -server to my board(nrf52840dk), eRPC-client to my PC and use UART as transport. The problem i faced is eRPC supports only CMSIS...
hello,i now get the IQ sample frome my DF demom, i use the putty to see the IQ sample.Here is my output in putty.
yes,i also use the python procedure of serial moudule...
I generate my keys add the dfu_public key to the example found in examples/dfu/secure_bootloader/pca10056_s140_debug. I then connect the board, erase all and program my nrf52840...
Hi
My device and Software details are as below
nRF52840 EVK
Softdevice:s140
SDK v16
I am new to BT and USB protocols.
As part of our POC I eed to test and establish...
Hi,
I have implemented a set of custom mesh models on nCS. In vendor models we have reset handlers, as in nrf documentation: https://developer.nordicsemi.com/nRF_Connect_SDK...
Hello,
We cant get a connection to our Matter Development Board like in the discription: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/connected-home-over...
This may just be more of a Zephyr question but wondering if anyone in the Nordic community has experience with this.
I'd like to generate code coverage reports when running...
Hi,
I'm developing a board based on the thingy91 (same nordic silicon, different sensors) and using nrf SDK v2.0.0
The blinky application is flashed and run correctly...
Hello, I am using the nRF connect SDK and am currently running into some issues with using the on board ADC. My issue relates to the adc_channel_setup function which returns...
Hello,
I am using an nRF52833 dev kit and the Zigbee light_switch example from nRF Connect SDK.
I was trying to implement the sleep mode so I wanted to estimate the power...
Hello,
I am having an issue with board bring up for a custom board I developed using the nrf5340 processor.
I have created firmware based off the peripheral_uart sample...
Dear Nordic support team,
I bought 3 piece of nRF52-DK from MOUSER, 1 piece of nRF52-DK version is 2.1.0 , and another 2 piece version is 3.0.0.
nRF52-DK version 2.1...
Hi there,
We're using nRF52840, IAR 8.40.1, nRF5_SDK_16.0.0_98a08e2. My question is, I need to toggle a GPIO pin right after SPI finishes the TX transaction and right before...
I am trying to use both USB and BLE on an NRF52840 using SDK 15. It hit a hard fault during initialization, specifically when it tries to enable the USBD IRQ.
It looks like...
