I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I was wondering how one might get the nRF9160 to enter the low power modes when making my own firmware? If possible could someone point me in the direction of an implementation...
We are building a gadget which senses temperature and humidity level using nrf5340 and using i2c as interface. We are using a slave which has SHT3X sensor for reading the...
I've been trying to use the NVS subsystem along with BLE and FOTA.
I got BLE and NVS working fine.
But if I enable FOTA (just including the code, not running an update...
I'm having trouble with a computer that can't run a Python script, which is using the library pc_ble_driver_py
I'm confused about the answer posted in
I've tried downloading...
Hi!
For a custom project, I need to enable and disable soft device for power consumption optimization. I've followed ble_app_gzll to enable and disable soft device. Unfortunately...
Hello,
I'm using the nRF52840 DK, SDK 17.1.0 and SoftDevice S140. My project is based on the Blinky peripheral example. The problem is the following:
Basically, turning...
I see a lot of threads about how you need to disable the UART while you're not using it because it has a couple of milliamps power consumption.
However, most of those threads...
Hello Team,
We are in process of designing our product with nRF52833. To secure our product and possible Firmware readouts, we are planning to use the APPROTECT feature...
So, I'm working on a project with two RGB LEDs, that's going to be powered by a coin cell. The device is going to spend most of it's time asleep, only waking up for a minute...
Hello - The nRF Connect for VS Code extensions updated today and it appears to have broken then nRF Terminal connection monitoring.
Old Behavior
Connect to device...
Hi,
I have a nRF52840-DK which comes with an o n-board SEGGER J-Link debugger/programmer to use with the internal microcontroller or an external one.
Also, I bought a...
Hello Sir/Madam,
I'm using Nrf52833 for ble_uart + saadc but this device given only 2 meter distance range .I want to increase that distance range.
How to increase distance...
Hi
I want to communicate with nRF52BK (nRF52832) board via its UART.
Eventual goal: Get Android device, acting as USB host, to connect with nRF52DK board's UART Short...
Hi.
I'm trying to run the http client sample for nrf9160 using nRF Connect SDK, but when I flash the board it gives this output:
Waiting for network.. Failed to connect...
