I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
The nPM1304 requires the CC1 and CC2 pins to be connected to the USBC port. Can they be left open/grounded on the IC side?
The problem which arose is that CC1 and CC2 are...
Hi, I'm looking for clarification whether the DECT NR+ modem firmware supports GNSS. Legacy docs say it doesn't, but there is no mention of it in current docs. Based on that...
Hi,
Issue
With the official nRF21540-EK + nRF54L15DK setup, my app/config works: advertising, connections, and PA/LNA behavior are all OK.
On my custom PCB ...
I am attempting to do channel sounding with one initiator and two reflectors. Switching between reflectors, by connecting to each in turn, does work, but it is very slow....
Hi Support Team
The attachment is ANT+ Device Profile for Bike Radar, it mentioned that an ANT+ Bike Light and Bike Radar Sensor can be combined as a single device, but...
Hello,
For a project with nRF9151 as the main microcontroller, we use nPM1300 for power management.
As I understand, for nRF9151, VDD voltage should be supplied prior...
I am developing a simple ble peripheral device that will measure temperature and humidity. For the most
part, it's working but I can't get the behavior I expect when enabling...
I'm a new software developer and I'm not a native English speaker. I ask questions through a translator now, the description might not be clear.
I am currently working on...
Hello,
I would like to know how to disable the NFC function with nRF SDK 3.1.0
I would build the Matter thermostat sample. I tried this: `CONFIG_CHIP_NFC_COMMISSIONING...
Hello,
I am trying to read the MCUBootloader version from the NS (TFM) application. I am able to read it in the Secure application using the fw_info_find function in this...
Hello,
I’m trying to run **LVGL 9.3** on a **nRF52840 DK** with a **2.8" ILI9341 TFT display (SPI)** using **NCS v3.1.0 / Zephyr 4.1 / Toolchain v3.1.0** .
### Problem...
Hello, I want to check the component alignment on the layout.
My layout is different than the reference.
Where should I connect the VNA?
Can I calibrate it on the PCB?
Hi,
I am using a custom nRF9160 board with the nRF7002 Wi-Fi chip via SPI, running NCS v2.9.2 . My goal is to connect to a Wi-Fi network.
However, during initialization...
I want to change the start address of the app in the ESB example from nCS 3.0.2. By default, after compiling and flashing, the program runs from address 0x0. I want to change...
