I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hello,
while migrating our FruityMesh framework to SDK17 I went through all SDK and SoftDevice release notes and migration documents and saw the following:
Now, to...
Hi Nordic Team,
Few questions about Power supply supervisor block of nRF52810. My device's supply volage (VDD) is 2 volt. I have enabled POFCON and the handler is getting...
Hello. I am designing an application where the goal is to send a notification, sleep for 1 second, send another etc.
To do this I used the application designed in this guide...
Hello,
I'm working on KX132-1211 accelerometer with nRF52832 and am using I2C(TWI) protocol. For that I need to create driver files even I was contact with manufactural...
Hi,
I have a model_handler.c which builds fine, but the moment I change it to model_handler.cpp, I get build errors saying "duplicate descriptor is not allowed". I am struggling...
Hi, There is code for vendor model element creation in nCS provided Chat client sample, as in below:
This works fine in "model_handler.c",
But when I import the same...
nrfjprog checks the target for 0xFFFFFF before attempting to write.
It should be successful not only if attempt to write the same value as is already present but also
...
Hei, jeg evalurere et Reinsdyr projekt der 30 Reinsdyr skal løper inne i en binge, er det mulig å motta kun beacon fra BLE taggen i nRFAPP fra de 30, hva er max antall når...
Hi!
Using the nrf5340-DK, I am preparing a code to be used on a custom board, where the pinning configuration will be different from that of the development board. I have...
Hi
I am using the nrf Connect extension in Visual Studio Code on a Window 11 machine together with C:\Nrf_Connect_SDK v1.9.1
After having installed the nrf Connect extension...
Hi,
I am working with nRF52832_dvk board, i am testing the OTA example as per in this link. https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts...
Hello, I'm starting to design the pcb for the nrf52840. I looked but I saw that it is also possible to create it on two layers instead of four as the reference design teaches...
Hi,
I am trying to burst read FIFO of ADXL362 with zephyr adxl362 sample. 1 byte tx (read fifo command) and n byte rx ( reading the fifo data);
Zephyr is the last version...
Hi,
We tried to use Connect Interval 7.5ms with MTU 88B, both central and peripheral role are 52832, but observed disconnection after 30 sec.
Disconnection reason is 0x13...
Hello all,
Background: -NRF5340 -NRF SDK 1.9 -Zephyr 2.7.99
My objective is to send a data of 768 bytes by BLE. I use 4 notify to send this 768 bytes data (192 packets...
