Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
I am trying to use a PPK II on Chromebook Linux. The nRF Connect for Desktop software installs and runs but does not recognize the PPK II hardware. I have allowed...
Hi, I'm trying to write an app to capture images from a camera and was wondering how to monitor changes on specifc defined pins in the board overlay file. For example if(...
The certification lab is testing nRF52840 RF .They need to test LE coded S=8,Payload Type：11111111：payload length：37
but i can't find Payload Type：11111111 in software nRF_DTM...
I am a beginner I want to advertise for some time then go to sleep mode and wake up do some tasks like advertising and go to sleep mode again. Do all this process recursively...
It looks like the nRF52840 only supports:
8 data bits
1/2 stop bits
even/no parity
So 7E1 is not a supportable mode...is this true? is there a possible work around...
Hi,
I am using nrf52840 and power it by voltage 3v using CR123A battery. As per datasheet minimum operating voltage is 1.7V. But i am facing controller reset at 2.5V. What...
How do we enable a PPI TASK for a GPIO output pin configured using zephyr GPIO driver API? ex: gpio_pin_configure_dt (&ex _pin , GPIO_OUTPUT );
If I just call nrfx_gpiote_out_task_enable...
Hi,
I'm having some trouble getting a device pointer for the OV7670 Camera. I've ported the OV7725 driver. It appears as if the program exits the driver before setting...
So I've been having an issue connecting JLink to programmer v2.2.0.
15:57:24.681
Using @nordicsemiconductor/nrf-device-lib-js version: 0.4.1
15:57:24.682
Using...
I'm trying to upgrade the nRF9160 modem FW on our nRF9160-DK. Programmer v2.2.2 indicates success but the at commands continue to return
at+cgmr
mfw_nrf9160_1.2.3
OK...
I am using the DPPI feature in the nRF5340 to trigger an SPI transaction from a GPIO edge with a delay.
In more detail:
GPIOTE IN event triggers RTC clear task
RTC compare...
Hello,
I've been trying to figure why calling sd_ble_gap_tx_power_set() continues to return the error NRF_ERROR_NO_MEM. I'm using SDK 17.0.2 with S113, v7.2.0 on the NRF52840...
Hi team,
Currently am working on PWM example from SDK i.e. (Nordic SDK v1.8.0), am testing the pwm example from the sample i'e v (1.8.0\zephyr\samples\basic\blinky_pwm)...
I have nrf52840 pcb without XTAL 32768Hz. When I flash it with Zephyr sample project "Peripheral uart" it doesnt work.
How can I config project to work without XTAL on the...
