I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello,
I am using nRF52840 microcontroller to communicate with an external integrated circuit, through I2C peripheral . The project is using the latest Nordic SDK: more...
Hello,
I am running 1\nRF5_SDK_17.1.0_ddde560\examples\dfu\secure_bootloader\pca10040_s132_ble\ses example of SDK 17.1.0. Now, I want to update the firmware when it is pressed...
Dear Ladies and Gentlemen,
I read for detecting angle of arrival the following page:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth...
Hi,
I want to develop simple app that receives data via BLE and send it through UART so I could gather them to file or draw a real-time chart in SerialPlot.
As far as...
Running the secure DFU example in SDK 17.1.0 results in hardfault in IAR EWARM 9.10.2. The board used is PCA10040.
Using EWARM 8.50.4 seems to work without problems.
Steps...
I have a number of custom projects and boards that were created using SES.
How do I get nRF Connect to see my projects and boars. I have a separate directly structure where...
if i am controlling two spi devices with one instance, can I just define a new SS in the same SPIconfiguration or do i have to close the connection and select a new one? ...
As soon as I plug in my nRF52840, the whole board gets extremely hot. When I try to upload a program, the error message "No J-link device connected" pops up.
With another...
Hi!
I use XMONITOR to get the current cellid but it seems strange.
%XMONITOR: 5,"","","24008","2725",7,20,"01ADF70B",215,6400,50,35,"","11100000","11100000","01001001...
I'm working on nRF9160-dk.
I built a sample application "serial lte modem" in NCS 1.6.1.
i can use AT command on the UART0, but i find the printk in source code is not...
I have successfully compiled my project using `west build` and now I am trying to load it onto my nrf5340 board I recently purchased. Here's what I'm doing:
- From the same...
Hi,
I would like to test some environments. Therefore - I would like to use an example from SDK 17.0.2, which allows me to connect to a PC via NFC, as a peripheral, receive...
I'am working on nRF52840-DK and nRF9160-DK.
i'd like to add an interrupt pin for a SPIM device. (eg. in the following spi_dev: )
&spi3 {
compatible = "nordic,nrf-spim...
Dear nordic team,
i want to take log from dfu example i tried using rtt veiwer but it doesnt work.im using sdk version 17.0.2 and soft device 7.2.0 and nrf52840 DK
in...
