I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello everyone,
We're developing an application that manages the LTE Link reconnections automatically, without interfering the GPS performance. For such purpose, when there...
I performed early software development on an nRF52840-DK. I'm using Zephyr on the nRF52840.
Now I have a custom board and started doing development on it by creating a ...
Hi Nordic experts,
Recently, I tested and found that I failed to start the advertisement with NCS 1.7.0 if the length of advertising data is greater than 251 Bytes, for...
Dear sir/madame
Start & stop of advertising and how to prevent automatically restart of advertising in case of a random disconnection or disconnection initiated from the...
Hi,
I've been scowering the SDK dicumentation and DevZone for this information without finding it. My apologies if this has been answered before.
When using the SUPL library...
Hello!
is it possible to execute some code in the section
or do i have to implement some kind of thread logic? or any kind of nonRTOS library?
I come from FreeRTOS development...
Hello,
The Example code is running, but only printF() statements are printing and to the PC terminal program.
The example calls for softdevice build 122.
I "think...
Hello,
I am working with the Thingy91 device and the SDK v1.3.0 asset tracker example (I am not interested in upgrading at the moment). I would like to know how I can save...
I flashed my board with DTM image, assign P0.20 for TX and P022 for RX. Most of the times the DTM application can't communicate with the nRF5340, maybe 1 out of 20 times,...
Hello,
I used to import our current project to segger embedded studio v5.62 from keil so I'm followed these instruction .
All project files are compiled well but problems...
On the nrf52840 module, when I first output to one of the GPIO pins when I load any softdevice ble_peripheral instance I have installed. 10 ms after the VDD pin is energized...
Hi,
I have nRF52840 DK, and PPKI power profiler, I measured peak current mA using PPK on Radio Transmitter, And I found there is a big discrepancy between measure and typical...
Hi Guys,
We are currently working on a mesh sensor network. I have already developed a vendor sensor model (client and server). The client will also work as a gateway and...
I have a couple of questions regarding the nRF52840 internal voltage regulators, specifically REG0. I couldn't find the answers from the datasheet and therefore I hope that...
I started using nRF Connect for VSCode a couple of days ago on one computer and it has been working great. Now I had to switch to a new computer where I had also just briefly...
