I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
At 1Mbps, UART will lose data when receiving. When I set it to 230400bps, it works well. I looked at the SDK code and found that too much time was spent in the receiving code...
Hi,
I had asked a question here few months back, about the maximum RSSI that can be seen on the nRF52832 chip.
https://devzone.nordicsemi.com/f/nordic-q-a/73578/maximum...
Hello.
We have several of our own manufactured boards, containing the nRF9160 cellular modem chip.
We use it for HTTP and HTTPS connectivity, on an application based on...
Hello. We are developing using nrf52832 (S132 v7.0.1, SDK v17.0.0).
I'm looking at how to encrypt a string with AES CBC. Below is the code we are considering.
Currently...
Hello.
I'd like to split an external QSPI flash chip so that part of the memory is accessible as raw blocks, and the other part holds a filesystem such as fatfs. Essentially...
Hi
I am using NCS version 1.5.0, I need to drive the GPIO pins of NRF5340 DK using the below library
"#include <nrfx/hal/nrf_gpio.h>"
While trying with this header...
Hello,
I am trying to run the example projects "ble_app_uart" in SDK17.0.2 on nRF52833DK, following the guide shown here: https://infocenter.nordicsemi.com/index.jsp?topic...
Hello,
1- we are using button-less secure bootloader.
2- Have successfully download our application image to the target via nRF Connect mobile App.
3- When target is...
Hello All,
I tried implementing basic cluster, Analog Input cluster and Power Config Cluster. My end application is report "measured tank level" using zigbee. For which...
I am trying the https_client sample and I can get it to work unchanged.
But I would like to connect to a different site than www.example .com.
As far as I can understand...
I'm running the ble_app_pwr_profiling example from the nrf5 SDK (16.0.0) and softdevice (s140 7.0.1) on a nrf52840DK (pca10056 2.0.1) and measuring power consumption using...
Hello, I am developing an application on nrf52840 using SDK 17. My application has a bootloader and sometimes when my application is restarting due to a command I send (using...
If we try to force terminate an ogoing BLE connection by invoking sd_ble_gap_disconnect, we don't receive the SD_BLE_GAP_DISCONNECT event in some cases even after the supervision...
One of my projects needs to use NB and GPS functions at the same time. When testing, I found that even though NB network is not transmitting data, after I start GPS, I often...
