Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hello,
I'd like to have the gcc linker calculate a checksum over a specific address range (defined in .ld file) and store that checksum at a specific address (defined...
example: peripheral nus device: nrf52832(Self-developed board) hi i run the example peripheral_nus , but it cannot work. Though i had set the RC clock. But when i run the...
Hi, I am developing a product that has a nRF52840 as the main MCU and it controls a Quectel BG95 (a LTE-M/NB-IoT module, powered by Qualcomm's 9205 LTE modem) using Zephyr...
Good Day,
Im a developer in switzerland using the nrf9160 trying to connect to the nrf cloud using mqtt, i have already flashed the credentials, updated the modems firmware...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
Hi all,
In Device Manager, my nRF52840 DK is recognized as follows:
JLink CDC UART Port (COM32) JLink CDC UART Port (COM33) USB Serial Device (COM22) — running a Zephyr...
I'm looking to use the new Zephyr support for the ProMicro nRF52840 board, which appears to be available in NCS v3.
However, Zigbee R23 only appears to target v2.9.0.
...
Dear devzone support,
I have a quick quesiton.
Why does the nrf5340_audio application only support 1 BIG, while the nrf_auraconfig support 2 BIG. Is it because of using...
Hello,
I'm adding power management to a custom driver that talks to a sensor via uart2 of the nRF9151DK. But from my tests it seems that uart_irq_rx_enable() has no effect...
Hi all,
I've got an existing OpenThread project for my workplace's metering product which currently is written for a TI CC2538 and I'm porting it across to run on a nRF52840...
Hi, I have a custom board with nrf54l15 and it does not have a 32 kHz crystal, it only has a 32 MHz crystal. Sometimes the code gets stuck at this line: Can it be related...
I have a peripheral which has an nRF53. It connects to either an Android of iOS phone. I've been testing add Connection Subrating. However I've been noticing that the Connection...
We have a Nordic 52840 based product which today we support with a custom gateway hardware. Now we want to write mobile apps (Android and IOS) to talk to this directly.
...
I have an NRF9160 system running and I see mention of " The nRF9160 PWM peripheral can capture the period and pulse width of an external PWM signal" but was a little confused...
DeviceTree Visual Editor shows SPI1 as enabled, but the changes are not reflected properly in the GUI or in build behavior.
I receive the following build error : " DT_N_S_soc_S_gpio_50000000...
