I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Trying to do ADV_DIRECT_IND advertisement.
We are trying to do the following advertisements
// ADV_IND Scannable and Connectable
// ADV_DIRECT_IND - Connectable...
I recently purchased an nRF52832 (XL52832-D01) for a wearables power management project. To test the module I flashed the basic blinky (zephyr). I'm using a ST-Link V2 as...
Hi
Brand new nRF52840-DK (PCA10056 rev 3.0.3, serial 1050245467, sticker on PCB). Never worked.
J-Link OB firmware update fails every time with: "Sending firmware data...
Hello! I am having troubles with my custom board using BL5340 from Ezurio. I have tried to flash it via my nrf5340 Audio DK but realized it doesnt support external Flashing...
Hi,
I am trying to set up a secure boot chain on nRF54L15dk with NCS 3.2.3 and an upgradable bootloader .
My intended boot chain is:
B0 / NSIB
S0 / S1 for the second...
Hello,
I would like to implement Device Firmware Update (DFU) over NFC.
Is this supported, and is there any recommended way to implement it? Are there any examples, reference...
I have two nRF52840DK boards that I was working with recently.
PCA10056 3.0.2 2024.33
I flashed one board with a BLE peripheral device code from the nRF connect sample...
Hello,
I'm using dmic module for sampling audio data from microphone. Recently I updated NCS to 3.2.2 and I started observing the following log: "Failed to allocate buffer...
After an update recently with the nRF Connect for VSCode Extension, it's been unable to find where my nRF Connect SDK is located when choosing a build configuration. It used...
Hi,
We are migrating from NRF52840 to NRF54L15 (QFN48).
I am using nrf54l15-qfaa-reference-layout-0_8 as reference but really struggle to understand some design choices...
Environment:
Board: nRF54L15DK ( nrf54l15dk/nrf54l15/ cpuapp )
NCS Version: v3.1.0
Zephyr OS: v3.7.99 (NCS fork) NOTE: I am building this over peripheral uart example...
Hi,
I am developing with NCS 3.0. In my application, I need to use MD5 to calculate a signature. Following Nordic AI's guidance, I enabled CONFIG_PSA_WANT_ALG_MD5=y in prj...
Hi,
I have got nRF54LM20-DK with the nRF7002-EBII add-on. I would like to know is there any recommended camera add-on for this hardware to develop vision based AI solutions...
