If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi,
I compiled and flashed my nrf52840-DK with "examples/peripheral/usbd_audio" and I noticed a few things:
Under Linux (Ubuntu 18.04) the microphone isn't listed. ...
We were use secure ble DFU and it work fine, recently we added serial DFU code with BLE DFU. Tested serial DFU with nrfutil and it also works. but problem in serial DFU is...
I try to invert the Signal on a PIN of the PWM module 0. It sould give out the inverted Signal of another PIN from the same PWM module.
I tried it like the code below...
We have problem in background DFU while updating Application with RBP,
Config: MCU : nRF52840 SDK : SDK16 Softdevice : s140_nrf52_7.0.1_softdevice (SDK16)
Case1:Programs...
Hi,
I'm trying to understand how to powermeter bike works. I read the ant documents and execute example bpwr ant code, but I have a question how cadence in power meters...
Hi, is it possible to reset the nvm in the nrf9160 modem back to factory settings?
I've made some changes using CFUN=0 and would now like to reset these back to as delivered...
I have an application using 4 wire SPI connecting to a 2MB data flash. An application using UART (no BLE) works fine reading and writing to this device. However with BLE enabled...
HI
I need to perform some RSA tasks on my NRF52832, but I don't see any RSA files under nrf_crypto folder of SDK v16. I am trying to use RSA from mbedtls external folder...
Hello:
I asked a question a few months ago
https://devzone.nordicsemi.com/f/nordic-q-a/54708/about-nrf52840-save-file-error
However, the follow-up did not get an answer...
Hi all,
I want to run ble_app_uart on my custom board.
I have the nRF52832 (PCA10040) connected with my board by SWD P19, SDK 16. Where should i change to make the code...
Hi, i must change IC nrf8001 to IC nRF5x. Is there an easy way to do this? I need the same same protocol of nrf8001 running on nRF5x for compatibility but with the possibility...
Hi,
I've been following the guide https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_thread.html#mandatory-configuration to get started with OpenThread development...
I have a product that advertises as a BLE beacon. It can be placed into BLE DFU mode through local actions (a command on the USB serial port).
Is it possible to add services...
Hello,
I have a question to ask, I want to beacon the temperature and humidity level in nRF Mesh project here .
Please give me some information or reference code...
