I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi,
I am testing the Peripheral Heart Rate Monitor with the Coded PHY application for the nRF52840-DK kit. So, I am using two kits, one running the Peripheral Heart Rate...
SDK version - v2.7.0
Project repository
Hi! I am a junior embedded systems software developer, and I just started working with Nordic's environment. This is my first...
Does the NRF8240 using the HCI UART sample support setting a public address?
https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/samples/bluetooth/hci_uart/README...
Hello, I made modifications based on the nrf9160 lte_ble_gateway demo. I modified the BLE.c file and changed the BLE connection to BLE scanning. The scanning algorithm is...
I am doing some development where I use the external flash for storage external to my application. When I enable MCUboot, I can no longer access the external flash. This is...
I am making a device using the nrf52dk that takes data from 5 separate sensors and sends the data to a nrf52840 dongle. My trouble lies with the ADC data collection. When...
Hi Devzone. I have a PCA10056 that I'm using to set up for CI / HIL testing, using an external nRF52840 on another PCB.
The external SWD on P19 is working perfectly.
...
I have achieved bluetooth direction finding using nRF52833DK. I would like to do the same with a custom board. I have used the BM833 chip for doing this. I have attached the...
Dear Nordic,
We made an attempt to use the external flash in the LwM2M sample.
We tried to follow this: docs.nordicsemi.com/.../nrf9160_external_flash.html
As soon as...
Hi.
When working with certain nRF connect SDK versions 2.x.x (not sure which range) in visual studio code, the build terminal outputs relative file paths when showing warnings...
I am looking for some simple slave and master samples to run on my dk's nut cant find any. in the intermediate course there is the master slave talking with the sensor but...
When will the nRF9151 Hardware Design Guidelines document be available?
We are currently leveraging information in the nRF9161 Hardware Design Guidelines document in the...
I am building a nrf52840 custom board and testing the ble_app_blink_pca10056_s140 example from segger I have a 32MHz crystal and a 32.768khz crystal And I added the following...
I've got a custom board using an nRF52832. I'm using the P0.06/P0.08 as the TX/RX pins for UART comms, but don't need the P0.05/P0.07 pins for CTS/RTS. Is there anyway I can...
Hello. I am currently working on a Mesh Network using the Nordic Thingy53 board. As far as I understand, the Mesh protocol developed by Nordic already has encryption, obfuscation...
