I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
When I use the command to read the software version, the message read by the Raspberry Pi does not appear " SoftwareVersion ".
Please confirm the attached LOG message
Hello,
I have a question about performing OTA via BLE (SMP) and using BLE mesh. Is it possible to perform OTA via BLE to ZigBee network and vice versa.
Since BLE is supported...
Hello,
I'm encountering issues while trying to install and update the nRF Connect SDK (NCS) environment on my macOS system.
NCS versions attempted: 2.2.0, 2.6.1
...
I am using nrf52840 to test the `periodic_adv_rsp` sample application using ncs. I had this use case where I would like to configure data in a subevent based on responses...
Hi Nordic community,
I'm starting this course as I'd like to start with Nordic.
I can't continue (better to say, start) the course as the instructions are different from...
Hello, I have an eval board of " nPM1100-EK -> PCA10123 0.8.0 " battery of li-po 3.7v 600mah battery termination voltage is 4.2V The above eval board works fine & the battery...
Greetings,
I'm trying to migrate the MAKEFILE configuration to SEGGER studio so that I could build and debug the project from there. So far, I'm stuck on the Linking part...
We are currently working on a Zigbee-based network coordinator using the nRF52840. I have a function, dfu_multi_image_write , that writes data to NVS in chunks. The function...
The Power Profiler app v4.2.0 release notes say:
"Updated PPK2 firmware to v1.2.0, which adds COM port for shell access"
Are there any instructions available how to use...
Hi,
My application is running NCS v2.5.3 on a nRF5340.
My project has FOTA via BLE, is running mcuboot, and is a multi-image build. I am trying to verify, from within...
Hello, I am trying to subscribe on a topic to get retained message.
I am using ncs 2.7.0
The problem is that whenever I am trying to subscribe to a certain topic, I have...
Dear all,
For a project we need to synchronize up to 5 data loggers, each of them is based on nRF52840. The sampling rate of some sensors can be of 1 kHz. I'm wondering...
Hi All,
I am lookging for a way to use the nRF7002 (or other 2.4 GHZ WifI solution) as a WiFi sniffer.
I want the solution to provide, for each WiFi packets in the previously...
my nRF52840 has MBR, SoftDevice, Application and Bootloader.
Can Bootloader call API in SD?
Will it be an issue? If I need to upgrade SD (could be a newer version),...
