I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
hello. I developed and tested the ncs/nrf/sample/bluetooth/multiple_adv_sets example using the nrf5340 DK board to suit my requirements. I want to run the source by inserting...
Hello,
We have a product which is a custom nRF52832 board, nRF5 SDK (didn't have time to upgrade to nRF Connect SDK), s132, BLE.
We used to call delete_bonds() function...
HI all,
I've found that adding a 10uF capacitor to the 52805 beacon reduces the power consumption, especially after speeding up the broadcast interval (100ms broadcast interval...
Using the Nordic NRF54L15 as part of the nRF54L15-PDK(v0.7.0).
I am working on enabling and experimenting with adding mcuboot and enabling DFU support via BLE.
I have...
Hi. I'm going to decode JWT (ECDSA sign) but I'm stuck. There is simple example to sign payload, but how can I decode JWT which I get from another device via bluetooth? I...
Hi to all,
I'm developing a beacon application on the nRF52840-DK starting from the example that I found in the VS Code (Zephyr).
I'm designing a custom board with only...
In my last question, devzone.nordicsemi.com/.../can-cis-and-bis-modes-work-at-the-same-time-or-switching-freely , I have asked that if the CIS and BIS modes can work at the...
Hi I'm trying to debug the record_text example in the nrf connect sdk. However when I attached my nrf5340 dk and hit debug in the nrf connect extension, the process stops...
Hello,
I am creating a new project that uses the nRF52810 as my controller, and during the development stage, I am using the PCA10040 nRF52832 development board. (I read...
Hello!
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am using two nRF52840...
Hi,
I have ordered custom board based on nRF52840 SoC couple of times from JLCPCB and that included assembling as well. Unfortunately, 90% of the boards had floating aQFN...
Hi,
I'm using the Bluetooth sample called Central HIDS and want to develop a feature that stops BT scanning after a few minutes.
However, during development, I encountered...
Hello,
I am using a nrf Development kit and I have it plugged in into a mac laptop. It works fine, but I keep getting the message that says:
Disk Not Ejected Properly...
Hello,
I have a question regarding the consumption of the nRF9161 DK board when it is under the following conditions: MCU on IDLE, modem off, wake on GPIOTE input (event...