Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
Hi,
I am working on internal flash nRF52832 merged with twi sensor, my sensor function will return a string . How to assign the string to the my_data.p_data . i am getting...
We use the https://api.nrfcloud.com/v1#tag/IP-Devices/operation/OnboardDevices endpoint to create and onboard new devices.
Recently, with no changes to code or certificates...
Some questions during the development of a DF project using the nRF52833DK:
Will excessive serial output affect the performance of the microcontroller? For example,...
Hello,
On my custom board, after upgrading from NCS version 2.5.1 to 2.6.1, BLE stopped working.
I get immediately the following trace after calling bt_enable(NULL)
...
I'm migrating from ncs v2.3.0 to ncs 2.6.1 in order to have the ram retetion working with the mcu boot.
But after some modification on my board file using a nrf5340 I get...
I have a custom board file which is based on nrf9160, I want to use it using the west build command and later flash it. I tried the steps under this tutorial: Nordic academy...
Just upgraded to NRF v 2.6.0 (Mac OS; VS Code). Our code previous built and ran successfully on our custom board with v 2.5.0 of the SDK.
Now we get the following error...
Hi all,
I'm developing a project on top of nRF5340. Thus I created a custom board definition in my project area:
That is a direct copy of ncs/zephyr/boards/arm/nrf5340dk_nrf5340...
Hello,
we are trying to use the nRF9160 as a serial modem for a Raspberry Pi running on Debian.
The application is basically the nRF sample "nrf\samples\cellular\modem_shell...
Hi,
I'm trying to build the Serial LTE Modem in my nrf9160 SIP custom board to communicate the STM32 MCU with the nrf9160 using AT Commands via uart.
My physical connections...
Hi,
I created a custom service in accordance with NUS service. I am able to assign all handles, subscribe to notifications. But I am not able to read any data from the device...
Based on my understanding on SPI signal, CS/SS pin need to pull down to low when read/write and pull up high when the action is finished.
May I know if this feature has...
I'm currently working on a project that uses the MLX90640 IR sensor. By default, this device has an I2C address of 0x33, but it can be set up with one of 127 different I2C...
Sifting through previous posts about redirecting printf to uart by using retarget.c, I have found this will work on previous versions of segger (5.42). Has anyone gotten it...
I tried adding the following settings to prj.config
CONFIG_CHIP_OTA_REQUESTOR=n
CONFIG_CHIP_QSPI_NOR=n
I've also tried to modify the Devicetree to be the qspi part in...
Hello, I have a project sampling a ADC. It has a INT output signaling new data is ready to be read with max sampling rate of 125ksps. I am using the interrupt and then reading...
