Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi there, i have a thingy91 for the electromaker contest. I've flashed the nrf51 bridge firmware using MCUboot. All went well. However, when i try to put in DFU mode the nrf9160...
Rookie question.
Finally I put my ble working passing a number thanks to the support from this forum. But now my problem is how to send a string with around 100 characters...
Hello nordic team, Question 1 How can I customize the Asset Tracker v1 to send Asset Orientation "FLIP" in the same frequency as the temperature and the rest of the values...
When communication fails on NRF connectivity dongle (In Python via pc_ble_driver) and Error code: NRF_ERROR_BUSY is received on attempts to write and one restarts python script...
Hi,
I am following below link for DFU over BLE. Link ( https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs-dfu ) currently it is working fine...
Hello ,
I'm using the libuarte library so i can send data and receive it , i'm enabling RTC2,TIMER1,TIMER0 and TIMER2 .
this is the main definition of my libuarte NRF_LIBUARTE_ASYNC_DEFINE...
I'm running into an odd problem with the PWM driver. We're using SDK 17.0.2 and the S113 softdevice on an nRF52833. We're using the PWM module to drive some LEDs.
The nRF52833...
1. nRF Connect SDK v1.9.1
2. Segger 5.68
3. sample name : multiple_adv_sets
I am developing through multiple_adv_sets.
I want to test by changing the uuid in uuid...
Hello
I have installed NRF Connect for Desktop in my system (64bit, i3 CPU). I want to debug my custom hardware using the nRF9160 Development Kit. I have connected the nRF9160...
We have a big application bigger than 500ko and we need a littlefs partition, so we end up with a mcuboot_secondary smaller than the mcuboot_primary (actually we put it to...
Hello, as stated in the Titel im trying to read Firmware Information, for Example the Firmware Version. I tried solving this by reading via Flashareas but no matter where...
Hi,
Datasheet says the sequence as mentioned below,
But the code given in the nordic playground does not follow the sequence mentioned in the datasheet, and the code...
Dear members, with success I implemented the time synchronization example from the nRF5 SDK guide. This example works perfect for a single master, but what if the master changes...
Hi Nordic:
How to use GZLL in nRF52833.
It is only has PCA10040 and PCA10056 In "gzll_ack_payload", but nRF52833 is PCA10100.
I try to use PCA10040 run in nRF52833,...
