I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
We plan to incorporate the nRF9160 into many thousands of our devices, however this leads to a question of procuring SIM cards. We purchased a Thingy91 to test the connectivity...
The iBASIS sim card came with Thingy:91 does not work. Got the replacement card today. However, I cannot finish the nRF cloud reg process. The new error message said
Tenant...
Hello, I am trying to load a sample project in VS Code using the nRF Connect SDK extension.
I try to load a sample project, click on "Create Application", and nothing...
I am trying to use the NRFx Softdevice controller, with Rust and the nRF5340. I have successfully initialized the library, but when I try to start to start advertising the...
Hi! I'm unable to connect my development kit to a network with the provided iBasis SIM card. I'm located in Bristol UK. According to this [ https://ibasis.com/solutions/iot...
To provide feedback to the user through the LED state, I would like the behavior to be something like this:
If the nRF52840 Zigbee device is unpaired and ready for a ZC...
Hi support,
I'm currently having issue trying to program a nrf52833 device using Jlink mini on mac. I have no problem programming the device using a pro Jlink on windows...
Hi,
I'm trying to use examples. The ICM42605 example does not work.
I get the following errors.
There seems to be an error in the code below.
It was tested with...
Hello !
I have found that error free decryption ( MIC error) on fly depends from S1LEN configuration value.
S1LEN have valid range value for each radio mode
2Mbit 1...
I'm getting an occasional NRF_LIBUARTE_ASYNC_EVT_OVERRUN_ERROR, it often takes over 24 hours to reproduce, and the libuarte appears to be generating garbage after the error...
Hello Sirs
I am using NRF5340 chip in my custom board to use the BLE radio and uart hard ware at the same time. The sample code which has been used for this purpose is ...
I have a BLE device with a MIC, which collects voice data and coded to BroadVoice 32k.
So I want to design a central to get this voice data.
What I think is use 52840...
Hi,
Why do all of these AT instructions fail?
1.AT%XPRODDONE=0
2.AT%XPRODDONE=1
3.AT%XRFTEST
4.AT%XEMPR
Thank you for all your assistance. Kind regards, Peter...
Hi,
Since adding a custom board to a app from a sample, the Flash button:
Has stopped working properly.
When i press it, a build is initiated, but the flash does not...
Hi,
I have been programming my custom board using SWD on a DK. It worked fine when I tried blinky example, however, when I tried nrf_ble_uart example, it stopped at the...
