Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
Hello,
I am trying to figure out a problem with the WDT module behavior
Running on an nrf52832 and using SDK 11 with softdevice s132 v2.0.0!
There are 3 WDT channels...
Hi,
I have nRF52840 DK with Power Profiler PPKI. It was working for long time, but now it suddenly stops working.
Screen saved:
nRFConnect Dektop version 3.7.1, Power...
After I changed from SDK 17.0.2 to SDK 17.1.0 I get for the example project "blinky_FreeRTOS_pca10040" during the compilation with IAR Embedded Workbench IDE - Arm 8.50.9...
Hi, I had designed custom board using icm20948. i tried to get raw values from sensor and succeed then i had ported nucleo code for nrf53 zephyr. when i tried to run below...
Hello,
I'm evaluating nrf52840 and trying to use zigbee/light_bulb as a starting point. One thing I caught immediately and still trying to find an explanation for was the...
Hi DevZone,
I need help to understand the DFU procedure over the Mesh without any second BLE dongle/BLE serial device to populate the DFU packets.
The ask is how can we...
Hi
I am using the nRF52840 with an external sensor which I need to config (nRF is the master). after this, nRF is acting like a I2C slave (twis) and i like to trigger an...
Hi,
I'm making my own program to upgrade the nRF9160's modem firmware over SWD. So far, application note nAN41 has helped a lot, but I'm getting stuck when trying to get...
Hello.
I need to transfer files from a phone to a BLE peripheral device. I have a small FatFS filesystem on an external flash chip on the device, and I'm now trying to decide...
Hi,
I have just setup the nRF Connect SDK for the first time. I am running Ubuntu 20.04 in a Virtual Machine. I followed the instructions in the "Getting Started Assistant...
Hi!
I'm trying to prepare FOTA firmware using instructions provided by: FOTA upgrades but it seems not working.I have couple of issues and questions. Please help me.
My...
Hello,
I have been experimenting with the new VSCode extension for the last week or so and I've noticed some issues. I understand that this is a currently a beta release...
Hello,
Is it possible to receive a review for a board i'm developing??
This board is to be used as a Raspberry Pi Hat to be able to communicate using UART between RPi...
How to recover communication due sequence number. (Could be due of PYACI serial hardware changed/dammaged). Is there any command to reset or know sequence number of node....
Hello all,
I'm developing a BLE CGMS application based on the experimental example on the SDK folder.
Now I working in the timing characteristics and I could see that...
