Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi,
We have been working with a coordinator and a router device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
Both devices are Zigbee 3.0 and implement...
I have a binary file for a 3rd party device that the manufacturer has asked me to test on their devices. I have looked through the ZigBee OTA example documentation but it...
Hello:
I am working on a USB bootloader where I have enabled the WDT on entry. After I enable the WDT, the app_timer is set to feed the WDT and to also signal the end of...
Hi
I have a new Thingy:91 that I'm updating.
After I updated the modem software and the firmware with Connect desktop Programmer.
When i could not connect I deleted...
We recently had an issue where a race-condition was caused because we handled entry to sleep mode a bit too carefully. Therefore, I wanted to discuss different methods to...
Hello!
USing help from this forum i have successfullz transmitted adc value from one pin of AIN# to ble and reasing values successfullz but now i am facing an issue that...
Hi Nordic Team：
I use version is: nRF52840 DK Version：nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8\examples\thread\ncp\ftd\uart\hex
Raspberry Pi 3 Version：RaspPi_OT_Border_Router_Demo_v4...
I am new to nrf52.
I want to configure TIMER1 as a counter.
However it does not count. I have added it after advertisement_init
Does the nrf52 have any such limitations...
Hii nordic;
I need to encrypt and decrypt my advertising data i.e;UUID,Major,Minor,etc.; of my nrf52832
So it cannot be seen by third parties
my sdk version is 15...
While trying to communicate through I2C/TWI with a MCP39F521 using a NRF52 DK (NRF52832), the first bit of the received data is always 1. The NRF52 DK is the TWI Master and...
Hi, I'm newbie to nRF DKs but started trying to run examples from pc-ble-driver-py / pc_ble_driver_py / examples / on github in order to get familiar with the nRF52840. I...
Hello
I'm setting up a set of Thingy91 and Thing52 units.
1) I registered 2 thingy91 sim cards and registered the nodes. 2) I see the SIM card in my account on nrfcloud...
I'm using a nRF52480 DK board with an adafruit 3421 I2S microphone breakout board attached. I am on Ubuntu 20.04 with SES 5.42c and SDK 16.
I am using a variant of the usbd_cdc_acm...
Hi,all
I am developing a Bluetooth product with HID function.I refer to the official keyboard example.I modified the "report_map_data" to implement some special keystrokes...
Hi Nordics,
we would like to evaluate the possibility of using NVM to store user settings. Based on the following searches, we still have some queries.
infocenter.nordicsemi...
