Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
when I send notifications or indications to central device without bonding it works perfect. But after bonding they are not sent. I receive following logs when cetnral...
I am using nRF52840 dongle and nRF SDK version nRF5_SDK_17.0.0_9d13099.
When I am trying to debug the application it gives an error.
using your example project on nRF52840...
I can't go into too many details, but the scenario we have is:
We have an NRF52840 device connected to a PC through serial (for both power and communication) The NRF device...
I am trying to create a minimum working Keil uVision 5 S132 project with PCA100400. When I compare the examples with mine, I notice that during startup, when the code of flashed...
Hi
I heard in the "nRF Connect SDK" presentation from May 2020, that the nrfSDK only support BT 5.0.
Is this still correct that the features of BT5.1 and BT5.2 are not...
Hello,
I want to use RAM to keep some data after a soft reset, so that I can find problems after reset. And I also found some implementation methods, such as using .non_init...
Hi so I ran this example:
https://devzone.nordicsemi.com/f/nordic-q-a/40476/unable-to-convert-to-long-range-after-looking-at-umpteen-examples--/157426#157426
When I went...
I need BLE sniffer and I puchase this device because in this manual of "nRF Sniffer" say that "nRF52840 Development Kit (PCA10056) " is compatible.
https://infocenter...
Hi,
Looking at the footprint you supply for the aQFN73 package (I have looked at the one supplied for nRF52840), I see that the pad have a size = 0.275mm. If IPC-7351 is...
Hello,
We have a product that sends out an ESB message approximately ever second, it does this using the RTC timer with the following setting:
It sends the message...
We want to add the nRF52805 to an existing product but also want to have the option to perform a firmware update.
The current DFU implementation doesn't allow the softdevice...
Dear friend Through github: github.com/.../v6.0.1 downloaded nrfutil.exe windows executable file, it can run perfectly on windows 64 bit. However, it will prompt incompatibility...
Hi, all,
I am working on nRF52832 using pc-ble-driver-py bindings to interface my BLE peripheral. Now I want to build the BLE communication between one central to multi...
Hi
AFter setting the switch sw5 to nRF91, itried to update the firmware using nRF connect V3.4.2
I got the following Error
Error while probing devices: Error occured...
