Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi,
I have made a custom board with u-blox bmd-340-A-R-01 module and trying to erase the flash with PCA10040 DK. I am getting error when I try: nrfjprof -e. Please find...
Serial Example in Mesh SDK allowed embedded system to provision a Mesh network
by interactive_pyaci.py controlling nRF52 with serial example with UART.
But the example...
Hi Nordic
SDK15.2 based application and bootloader running on NRF52840 based UBlox module.
We have the following symptoms happening in the field:
- 2 channels of the...
The customer wants to implement a hid function like the nrf52840 on the nrr9160, and there are no off-the-shelf routines or references to add the hid function.
Hi everyone,
I need your advice regarding the regulator configuration of nRF52840
I am designing my own PCB using Raytac's module MDBT50Q-1MV2 that carries on the nRF52840...
Is this the right cable to program the Thingy 91 using nRF9160-DK?
https://www.digikey.com/products/en/cable-assemblies/rectangular-cable-assemblies/450?k=adafruit%201675...
Hi,
I've developed a custom board with nRF5340-QKAA (see schematic sheet attached). nRF5340's VDD pins are not tied to VDDH pin, then I assume the nRF5340 automatically...
I tried to build the OpenThread CLI sample in nrfConnect SDK 3.1 with the version of Segger as installed by the ToolChain Manager. 4.52 on a nRF52840 DK board.
This is the...
Hi I am now aiming to progress ota with android application. Following the guidelines on ithub, I created a class DfuService, NotificationActivity. The class internal code...
HI All,
I am trying to modify the default spi example code. Here i want to toggle the SS line for every bytes transfer , Please suggest how do i can achieve this ?
If...
Hi,
I am using nrf9160 module and want communicate with cloud via NB-iot network.
But I don't have idea that NB-iot supported in India or not.can you please help here...
Hi,
I'm trying to include a library written in C++ which requires at least GNU++11. Unfortunately if I switch the C++ compiler in SES I get the following error:
Is there...
Hi there, I have been trying recently to DFU a custom device using desktop nrf connect, and I get an error message as in the following picture right after pressing start DFU...
Hello,
Currently we working on a project that uses:
- nRF9160
- Zyphre OS
- Segger Embedded Studio for Arm (Nordic Edition) V4.52
- SDK v1.2
I saw in others...
Hello, i have configured the Timer1 as follows
ISR_DIRECT_DECLARE(timer_handler){
if (NRF_TIMER1->EVENTS_COMPARE[0]){ NRF_TIMER1->EVENTS_COMPARE[0] = 0;
gpio_pin_toggle...