Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi.I had been confused with parameters of sd_ble_gatts_characteristic_add( ).If I set parameters
like that:
static uint8_t ast_notify_char;
..........................
HI,
I have to implement buttonless bootloader.I am having simple doubt.I am programming softdevice,application(Hrs example with bootloader),bootloader hex file using nrfgostudio...
Hi,
I am trying to perform RF production testing using nRF51 development kit. My DUT is another nRF51 DK. I am setting my DUT according to Figure 2 mentioned in nAN 34...
HI,all
when i want to notify with MITM,there is an issue with my project.
my central role device is IPHONE and the app is lightblue .
When i enabel notify ,the nrf52382...
Hello,
I am using battery (3V) to supply nRF51822 system and the circuit is made according to DCDC mode circuit. My question is :
what is lowest voltage the battery can...
I have two p_storage_param modules param and param2 . param would store 3 blocks of 16 bytes and param2 would store 10240 bytes (10 pages). I called pstorage_register (param2...
Hello,
I followed both tutorials about using Eclipse GCC and migrating to peer manager.
I get no error when I follow them individually, i.e. when I use the project included...
Hi,
I developed an application based on s110 using the nrf51 DK and it works fine. The DK is based on a nrf51422 QFAC which is the biggest one in terms of memory sizes. Now...
Hi,
the mesh_dfu.c requires the definition of tx_config_t, which I can't find anywhere in the repo branch sdk-8-support. Same with RBC_MESH_EVENT_TYPE_DFU_SOURCE and other...
Hello,
This is in reference to the following:
devzone.nordicsemi.com/.../
The post talks about the maximum size of application that one can in order to be able to...
I'm trying to get the PWM example to compile in SDK 10. However I cannot get app_pwm.h to compile. I get the following errors:
expected expression before '{' token ble_app_hrs...
Hi All,
We are in design Phase of our product and would like to use NRF52 Chipsets for it. Please Clarify our query regarding it.
I have two Nordic NRF52 Chipsets , One...
Hello:
Im using SDK 10 with softdevice V130.
Im opening UART:
uint32_t err_code;
const app_uart_comm_params_t comm_params =
{
RX_PIN_NUMBER,
TX_PIN_NUMBER,...
Hi,
In nRF52832_OPS_v0.6.3.pdf chapter 16 Power-Power management.
It describle as follow:
Automatic switching between LDO and DC/DC regulator based on load to maximize...
Hi all
I found the following thread that mentions that the "radio test example" can be used for FCC testing:
devzone.nordicsemi.com/.../
Now the certification lab...
