I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Hello,
I'm working on an application where we're implementing the nPM1300 and utilizing the fuel gauge algorithm to estimate battery life. Interestingly, the results that...
Hello,
I am attempting to connect a ST7789 to the nRF9161 and communicate with SPI. However the display is not working and I suspect it is because the gpios output the VDD...
Dear All,
When i connect the nRF5340 Audio DK to the windows PC through the USB, It will be enumerated as a USB audio device.
And then, It will act as the default audio...
Hi, I'm currently using nrf52840 MCU for product development and almost finished my project. What I want is when producing a product, I want to compare the checksum of the...
I am trying ADC readings for connecting my sensors. To better understand and see the values, I have made a simple connection with 4 10k Resistros in series, VCC on top and...
I am working on an nRF52832-based project and I am encountering an issue with achieving low sleep current. Despite setting the TX power to 0 dBm and the advertising interval...
I am thinking of using the sample source code of nRF5340 Audio to realize LE-Audio on a board created by our company.
I have written the source code of nRF5340 Audio to...
Hi, I am pretty new to programming with NRF boards and I've hit a bit of a roadblock.
I started with the BLE Event Trigger example and I have managed to retrieve BLE advertising...
HI Noridc
I am developing with nRF5340, and I need to proceed with DTM test to verify the chip in the production process.
I am currently using this routine C:\ncs\v2.6...
Hi, I'm working on a ble peripheral that uses nRF5340, NCS recently upgraded to v2.6.1, Zephyr v3.4.99. The net core is running the HCI RPMsg controller sample as it is. In...
Greetings all. I am troubleshooting an issue on my BLE sniffer setup. While I don't 'think' this is causing my actual current failure (Wireshark not detecting COM6) I wanted...
hardware:nrf5340dk
case: Bluetooth: Direction finding central/peripheral
I modified the code to change the quantization level of the I and Q data received by the receiver...
hardware:nrf5340dk
case: Bluetooth: Direction finding central/peripheral
I added CONFIG_BT_DF_VS_CONN_IQ_REPORT_16_BITS_IQ_SAMPLES=y in the direction_finding_central...
Hello Team,
Just to give you a background , I am working on a project using the NRF Connect SDK and want to run my application from external flash memory. Specifically,...
Hi,
We have a custom board, where we assigned the following pins for SPI4M instance, and the intention is to use it with 32 MHz:
SCLK = P1.15
MISO = P1.14
MOSI = P1...
