Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Dear Concern,
We were developing one of our products using nrf52840. We previously used the nrf-52840 USB dongle for the product. Now we were moving to nrf52840 chip based...
Hi,
nRF5340 + nRF21540, NCS2.0.2, VScode
i follow Working with RF front-end modules — nRF Connect SDK 2.0.99 documentation (nordicsemi.com)
how to disable TX_EN? i only...
Hi,
I am using SDK 16.0.0 and nRF52833. In which TWI (master mode) is not working.
Pressure sensor is connected over I2C. (NRF_DRV_TWI_INSTANCE(0))
Previously I am...
Hi to all!
I'm trying to use the same GPIO to wake up the nrf52810 from system off and also use it to execute some functions. I have this code that is based on the example...
I'm trying to load a program to a custom pcb with a n52832 chip, but shows up this error in the Programmer: Failed to load readback protection status: async task failure for...
Hello,
I am working on a project that modified from ble_app_uart_c, with sdk v16.0, softdevice S140
In my case, I defined an event observer by
NRF_SDH_BLE_OBSERVER(m_ble_observer...
Dear Mate,
I am using bl653_dvk board i followed this link clearly (+) Add DFU support to your application - Software - nRF Connect SDK guides - Nordic DevZone (nordicsemi...
I am working on a project that need to receive extended advertising data, I modify periodic_sync from nrf connect sdk to get the data and it works for my device, but I need...
Hello,
I am testing current consumption of my custom board with PPK. There are some passive components (resistors, mlcc) on the board also with active components (accel...
Dear Nordic,
I want to scan slave devices , so I use TWIM nrfx driver to send zero byte data, I don't got error code, but I don't receive TWIM event too. I found a example...
Hi everyone,
I want to design PCB for nrf52840. Do you have any suggestions before i start?
I used STM32, PIC, Nuvoton and Atmel series IC's in my PCBs. But nrf52840...
Hi There,
I am working on a Door lock system using Nrf 52840 Chipsets having BLE and ZigBee Communication protocol. I wanted to have ZigBee OTA DFU feature in my product...
Hi there,
We are seeing a massive difference in UART current between the same revision 2.0.0 nrf5340 devkits. Below, with the UART enabled with HWFC and only the receiver...
