Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hello,
In my board, nRF52832 is connected to other MCU.
And those two communicates via SPI. nRF52832 is master.
To synchronize two boards, MOSI pin has to be used...
Hello,
Central uses nRF52840, and multiple peripherals use nRF52832.
The central is paired with each peripheral device , and each communicate.
To do this, I am developing...
I am testing smp_srv (bluetooth) with NCS 1.3.2. I don't know how to build and flash related apps for MCU boot in NCS. MCUboot is unable to boot smp_srv even after running...
Based on nRF52 hardware，I want to develop a phone based on HID protocol to control the phone, send instructions to let the phone into the lock screen state，
How to go about...
Hi, DevZone, thanks for help : )
I'm try to porting DK Board's Ble Bonding function to Target Board.
TARGET : nRF52840
SD: s140_nRF52_v7.0.1
SDK: nRF5_v16.0.0
...
To whom it concerns:
I'm a little new to Bluetooth SIGs launch studio and need a little guidance on the correct QDID to utilize for my product using Nordic SDKs.
I have...
Hello,
I'm working on a program that receives the temperature over TWI, saves the temperature in a string to flash memory, then adds this string to an NDEF message to be...
Hello,
I have 4Pcs same PCBAs and same firmware, the current values as below:
2.2uA
3.3uA
3.0uA
3.8uA
Condition: Power Supply 3V Battery; Temperature 22...
Shalom!
We have a nRF9160 custom board on which I cannot switch some of the IO lines.
For example we have two leds, P0.9 an P.10 but only P0.9 works. The hardware guy...
Hi there, now I set up a BLE to connect peripheral to central via NUS service. The peripheral is a customize board with nRF52832 and the central is nRF52840 DK board. The...
Hello everyone I hope summer's kind with you (or winter, for the southern hemisphere...)
Here's the deal: my printf and NRF_LOG_INFO output zeros, while my register clearly...
Hi Nordic team,
I am using nRF connect sdk mesh light_switch example. version of sdk is v1.6.1 .
The node is detected in the nRF mesh app in my mobile.
what does group...
I believe I'm following both the Cypress data sheet properly. Yet I'm still having an issue getting the simple QSPI Peripheral example to show data consistency.
Can it...
Hello
I want to operate SSD1331 OLED(96*94) using sdk v17.0.2 and nrf52840 custom board.
The OLED example of sdk v15 was replaced with the codes of sdk17 and tested on...
Hi Nordic experts,
Recently, I consulted the datasheet and tried to find out something about the radio speed when using softdevice, unfortunately, I can't find anything...
