Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
DeviceTree Visual Editor shows SPI1 as enabled, but the changes are not reflected properly in the GUI or in build behavior.
I receive the following build error : " DT_N_S_soc_S_gpio_50000000...
The nPM2100 datasheet (v1.0) provides Figure 8: Load current triggering mode change vs. VOUT.
Can you confirm:
1. Consider the system is in Low Power mode. If the load...
Hello,
I am trying to implement OTA through BLE, and as Im building the program, Im getting a build error as :
error: 'FLASH_DEVICE_BASE' undeclared (first use in this...
Hello. I have a light sensor connected to 2 gpio pins on nrf5340, Enable Pin : P0.08 and Output Pin: P0.07 Trying to trigger an interrupt based on the light. With the button...
hi support team,
docs says we can program 54l15 external spi flash ,please refer to : https://docs.nordicsemi.com/bundle/nrfutil/page/nrfutil-device/guides/programming_external_memory...
Hi,the Nordic team I'm working on low-power devices that Matter over threads by nrf54l15,I found a problem at present. I interrupted the configuration of the two PIR input...
Hi all,
I’m working on an nRF5340 project where the network core runs a hci_ipc firmware to forward HCI RAW packets to the application core, which then parses vendor-specific...
Hello DevZone!
All samples with Application Event Manager (CAF, nRF Desktop) has simple main function like that:
Main thread has terminated after executing and main...
Dear reader,
I am currently working on a project involving the NRF54L15 microcontroller. In the specifications of the MCU, under Circuit Configuration 1 for QFN48 (QFAA...
Hi I’m looking for some advice on what may be drawing power from the thingy 91x.
I have measured the power consumption of the nrf91 the nRF 5340 and the nRF 7002 using the...
I want to use P0.13 for ADC reading. However, I noticed that it is already used as an SCK pin in this configuration:
spi3_default: spi3_default { group1 { psels = <NRF_PSEL...
Hi!
I’m currently setting up multi-image DFU on the nRF5340 using external flash.
By following the official documentation and samples, I managed to get it working correctly...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
I'm getting timeout errors when trying to program a Thingy:91 with a J-Link Pro PoE on macOS on an ARM Apple M3 Max.
Here's the command and error message:
I get the...
Hi, can you please help me with configuring ras_initiator for channel sounding when using two antennas on the initiator and one antenna on the reflector ? I am starting from...
