I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi, all
I added a scanning module to the example 'ble_app_uart.c', so each one works well.
What I want to do is advertising and connect at the same time while connected...
What is the best practise for multichannel SAADC conversion in ultra low power devices? For example I have to measured 4 channel in interval 250ms. Below what I try:
...
Hi, Dear Nordic & all:
when I run the ble_app_hids_keyboard example in nrf52820(SDK17.0.2), I meet a question:
1、Frist I use my iphone connect ble device and pair success...
Dear Nordic:
so I want to know In nRF52 serials chips, How much HFCLK CONTROLLER ppm is the frequency offset distribution and production FT control range? Do you have any...
Dear all, now I am making a data sampling system with multi peripherals and one central. The peripherals sample data from sensor via SPI port and transmit data to the central...
Any SSD1306 example for nrf51822 ??? I found this but is for nrf52.. i try to add it for my nrf51822 but there are tons of functions with different declarations in my sdk...
I have nRF5340dk board and my question is that can I use only networking processor to run the BLE applications? If not why? As the Radio hardware is only connected to networking...
Hello , I want to read analog values from potentiometer using analog pin P0.04 (A0) on nrf5340 with zephyr ecosystem . Where can I get beginner documentation like setting...
Hi,
I'm a beginner, and currently working to implement a low-power controller using nRF52-DK and Power Profiler Kit (PPK).
I ran the following codes (system off) and expected...
I have setup a 1-1 paired central(+peripheral) <=> peripheral Central is a 52832, SDK 16.0, SD s132 v7.0.1 peripheral is a 52811, SDK 16.0, SD s112 v7.0.1 My code is based...
in this example
/root/ncs/nrf/applications/serial_lte_modem
I want to build_nrf9160dk_nrf9160 in secure mode
but compile error #ifndef CONFIG_TRUSTED_EXECUTION_NONSECURE...
Hello,
I am confused on which plateform I should use to program my nrf52832 chip.
First it is advertised to use Segger Embedded Studio that I am trying to configure...
Hi all. I am using Keil for programming a nrf51822 & SDK 12.3 I want to use the SSD1306 OLED Drivers in my project I follow these steps: 1) I copy .c and .h files form github...
Hello,
Im using a NRF52840 custom made board and im having some issue with the I2C communication. There are 3 units on the I2C line, the MCU and two sensors, the diagram...
Hello,
I am doing a project for college with nRF52840. It's about a mobile phone with an app that send the location of the device when a user touch a button. This message...
