Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hi,
I am not able to program an Acconeer xm122, which is powered by an 52840. It is mounted on the Acconeer xb122 shield. My nrf52832DK is connected to the shield using...
Hello DevZone,
I am using a nRF52840DK, with this I want to connect my DK to an external device, emulating just like a real device pairing. I want to do this and run some...
Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
I have understood that zephyr I2S APIs do not support NRF9160 ATM. Is that true?
Also, I could not find any samples about using NRFX I2S drivers on NRF9160. Are there any...
I have 2x Power Profiler Kit II up and running using the Power Profiler app - started twice and with separate PPK2 instances selected, as described in another support post...
Hello, I' needing some help on setting up the MCUBoot for the BL5340PA using the ncs 2.6.2. Currently I have the below add on for the prj.conf for the application core:
...
I would like to implement ble mesh direct forwarding feature in my code but i am not finding zephyr library for that. Is there any possibility to get link for zephyr direct...
Hello, I am using ISP1907 which has NRF52833. I get the IQ data and configuration from serial as: DF_BEGIN ['IQ', 0, 0, 11, -9, -213] ['IQ', 1, 8, 11, -209, 23] ['IQ', 2,...
I’m using SMP over UART to send the erase command ( {"slot": 1} ), and it only erases the application core image (image 0). I also have a network core image (image 1) present...
Hi All!
Hope you are doing well!
I am using nrf52833, NCS 2.3.0, Want to minimize the current consumption by sleep mode.
For this, I disabled the UART and SPI and the...
Hi
I have been studying the nRF Connect SDK and taking the courses at Nordic Dev Academy. In the Zephyr Fundamentals course, as I don't have the sensors used in lesson 6...
hello.
We're now planning to migrate our firmware library from nrf5 sdk 17.1.0 to stand alone nrfx v3.xx.x.
All our products are made with nrf5 sdk 17.1.0 using ses. ...
I’m using a custom PCB based on the Minew ME54BS01 module (nRF54L15 SoC) for both ends of our proof‑of‑concept: one node as a GATT‑based Channel‑Sounding reflector (leveraging...
Hi,
I am trying to port the DTM example to our board, 52833 based but when DTM is initialised I get about 1400ms of CW then:
00> *** Booting nRF Connect SDK v2.5.2 **...
