before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi,
We want to have same key for handling accept for LESC pairing and sleep mode if BLE is in advertising.
The implementation is based on ble_app_hrs_pca10040_s132.
...
Hi There
I am debugging my application board by light-swtich server project of Mesh example and " pca10056_s140_ble_debug " project of SDK example dfu.
My application...
Hi, I'm using nRF52832 Software Development Kit, PCA10040, S132.
Like the subject, I'd like to change 'ble_app_hrs_c' and connect it to my device.
I changed the service...
Hello,
I am running an application on nrf52840DK. It is using uart service to send a sensor data through BLE to Uart servic on smartphone. I want to measure the current...
Hello,
We just noticed that according to the Raw data detail in nRF Connect, we are able to advertise more than 31B data limit. Is that possible or do we incorrectly count...
Hello,
I am trying to figure out a way to configure the adc node using the .dts Device Tree file in a similar way to what is done for other nodes such as &spi and &i2c....
I've installed the nRF Connect SDK Master manually since I need the Zephyr modules for a school project. I've manually installed the SDK before without issues but on my new...
Hi Dev team,
I am working with a nRF9160DK board. I am currently getting an error while building my SPM folder in : C:\Users\adeel\ncs\v1.3.0\nrf\samples\nrf9160\spm.
...
Hello!
I'am from austria and try to connect a Thingy:91 to your nrf-Cloud. First I tried it with your
iBASIS sim-card, but in austria we can't use this card.
Then I...
Hi all.
I did a layout with NFC antenna with a nRF52832 chip.
In the schematic (suggesten on datasheet) I have antenna coil with 2 capacitors to ground.
Drawing...
Hello everyone.
I would like to set-up a mesh network of Thingy:52 devices and an nRF52840, which would help me communicate from the an external stimulus to the phone, via...
I have an application where the nrf52840 dongle is hooked to a sensor. The sensor drives a pin high, the mcu grabs data from the FIFO (SPI) and puts it in a buffer. So far...
Hi Team,
We need to use Flash as EEPROM and we have the following queries,
1. How much maximum size of Flash can be configured/emulated as EEPROM/NVM?
2. Whether below...
