Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
I could decrease current consumption at v1.2.0, but couldn't at 1.3.0. 520uA flows in k_cpu_idle();
How can you do that?
Also, in v1.3.0, CONFIG_UART_0_NRF_UARTE is depricated...
Hello
Good day!
Problem: We have got a new nrf52DK, and in our application development we use GPIO interrupts (we have set up 4 gpio interrupts). Surprisingly the GPIO...
Hi,
I'd like to know the units of measurement of the data obtained by the environmental sensors of the Thingy:91 device. I have found no information on that.
Temperature...
Hi,
I am currently working with the asset_tracker example and sending information by LTE-M of environmental and GPS data. I wanted to know if there is any way to calculate...
Hi,
I want to test eddystone example with nRF52833.
The default project doesn't include PCA10100.
I am trying to create one, but it always stuck in the function nrf_crypto_rng_backend_init...
I believe from reading some of the existing posts that my JLink EDU mini programmer (with SWD connection) should work with the nRF51822 (it shows up as a device option in...
Hi,
I want to build a bluetooth central example of zepher to nrf52832.
I am using the command "west build -p auto -b nrf52832_mdk samples\bluetooth\central" to build the...
I'm using 51822 QFAC, SDK11 S130 2.0.0.
I'm able to write to flash using fstorage_write() below. But the problem is whenever I put a for loop after I call fstorage_write...
Hi,
I built a simple custom board with an nRF52832 ebyte BLE module with no added components except for the RST and DFU buttons, the serial wiring are the same pins (RX...
Hi,
I'm working on a BLE scanner which need collect data from the beacon's scan response packet.
As far as I test, the current mesh beaconing example cannot get the scan...
I plan to use nrf52840 in high voltage mode (connected directly to the power source via VDDH pin) with button.
And I plan to use voltage regulator with EN pin (with pull...
The most relevant thread on this topic is two years old. I do not want to use Keil as it is so costly and the project may not go anywhere. I am not interesting in using the...
Is it possible for me to easily modify the nrf52 Zigbee samples to run on 1 or more of my 5340 M33 cores, or is it a rewrite?
I can see chip support for nrf52 but no mention...
Hello,
We recently sent a design to our board assembly house for review and they indicated that the large copper area under the nRF528323-CIAA (WLCSP) may result in head...
