If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I have just purchased 2 pcs. nRF52840 - one of them works fine - the other one reports this when i run dmesg on my linux (tested on 2 different systems) "Cannot enable. Maybe...
Hi,
I'm using nRF52832-CIAA.
VDD,Pin A7, tide with Cap 4.7uF 0603
VDD Pin H7 tide with Cap 100nF 0201
DEC3 100pF 0201
DEC2 100pF 0201
DEC4 1uF 0402
Using LDO...
So I'm kinda new to micro controllers and I followed the steps for the custom service tutorial ( https://github.com/bjornspockeli/custom_ble_service_example ), however when...
Using the scanner module, I set up a scan filter to scan for UUID with no auto connect. In the scan_evt_handler, I have a switch case for the NRF_BLE_SCAN_EVT_FILTER_MATCH...
I want to secure advertised packets using ccm
I am using s132 , SDK 14.2.0 and nrf52 dk
I found that AES-CCM peripheral is blocked by soft device usage and that I need...
I have this error.
In a last time with same error on a nRF52832 I decided this problem with increase:
On the 52832 it works. But on the 52810- project fall.
How to...
Hello,
I am using nRF52832 DK PCA10040 v1.2.4, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
As part of ble_evt_handler...
Hello All,
I am developing a custom board with nRF52832. All good with Segger Embedded Studio, I could download and debug the board successfully.
When I tryed to program...
Hi, i'm using nRF52840
I'm using 2 uarts :
one (uart0) is only for logging and another one (uart1) is for communication.
I can send from both uart, i can see i receive...
Hi
I sometimes get stuck in the zb_nrf52840_abort but the stack trace seams to be strange, its only containing two levels, Am I missing something or is there a better way...
Hello,
I have inherited a Thingy:52 project which was using some old versions of SDKs. Now I am trying to port it to a newer version in order to make it compatible with...
In nRF5_SDK_15.3.0 some undefined reference error reported when using nrf_drv_clock module (example: undefined reference to `nrf_drv_clock_hfclk_release)
The problem is...
Hi,
Is it possible to update the modem firmware once the product is on the field? I'm not talking about the application hosted on the M33, but the actual modem firmware...
Hi,
I'm testing pca10059 usb dongle with pc-ble-driver (not nrf-connect-pc)
I need 2M phy because of throughput.
latest pc-ble-driver support nrf52840 with softdevice...
