Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I am developing software supporting LEsecure using SDK 12.3 with nRF 51822.
Please tell me what to do when incorrect data is entered in "Passkey entry".
Currently...
Hi.
I've been trying to send a payload with STM32F but I can not. I've used both STM32F103 and STM32F3 to send a payload but neither of them worked. However, when I use...
Hi,
I use nRF5 SDK v15.0.0. In my application I need periodically disable and enable Bluetooth because they are wifi also, which connected to the same antenna. Its mean...
Hi,
I'm trying send me the mac address of the device by UART by the following method:
By serial I receive:
Start b9:24:82:d5:4f:81
The problem its that the device...
Good day
Firstly, an overview.
I am currently busy with a technical proposal for a client. Initial details will result in a completed approx 60 000+ sensor network. My...
Hi EveryBody!
I've begin to work with the n51 family, my board is based on a n51822QFAA H1 IC.
I use Keil5 MDK and a ST-Link V2 programmer. They work fine as I've tested...
IOS, nRF Toolbox 4.4.4, DFU Library version 4.1.1
Attempting to flash to ruuvi with nRF52832 reports
:INFO:Hash failure and
:INFO:Return false in CRC
to J-Link RTT...
Hi,
I'm trying to modify the slave latency and supervisory timeout setting, but found sometimes the gap_params_init() will get error after changing.
For example, I can...
I want to implement mesh functionality. There is no problem with nrf52dk board, but I think there is a problem with board that I made with nrf52832 chip. attach the photo...
I'm on SDK 15.2 and iOS 12 with nRF52832 on a custom board.
I've added the dfu service to my existing NUS/UART service. In the nRF connect app I can see both services and...
I have downloaded SDK software nRF5_SDK_15.2.0_9412b96. I am using segger studio as my IDE on windows.
I tried compiling the Example code for SAADC. There were no errors...
Hi, On SDK12.3 when using sd_flash_write at any memory location causes the device to halt and restart. On SDK11 I've been using flash_word_write and flash_page_erase using...
Hi I am using a nrf52832 board with a BMI160 sensor. I am trying to sample Accel and Gyro at 1600hz using a timer. The timer timeout is set at 20 ticks (32768/1600) @32768...
