Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
I'm trying to read a voltage from my power supply using the differential SAADC on my board to simulate the readings from a thermopile that I ordered so I can start calibrating...
Hello,
I am working with nrf51822 and I want to send data over ble to an android application which requires pairing. I modified the ble_app_uart example to read the data...
Hi Nordic Forum!
We're currently tuning our antenna since we runed with some problems during our EMC testing.
In that regard, what is the impedance (both input and output...
Hi,
Is there no specific code of ble_app_uart_coexist meant for PCA 10056 and eventually s140?
Or will the same code work for the nRF52840 board?
I am using SES and...
I want to use the nordic USB peripheral drivers to allow for the initialization of multiple devices. The end result of the project will be to have a single nordic creating...
I am using the nRF52832 (on Rigado BMD-300 EVAL kit). I am using keil IDE and nRF GO to upload my compiled code to my device. I am using SKD 15.2.0. Using Windows 10.
...
i donot know why,because other board is ok.
i am using this project
\nRF52832 pack\nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a\examples\ble_central\ble_app_uart_c...
I am migrating my project from SDK 15.0 to SDK 15.2. I was using CC310 to accelerate crypto in the bootloader.
While builiding the bootloader wit SDK 15.2, I got the error...
Hi team, Does the nordic chip receive a Bluetooth signal being communicated with a mouse, keyboard, cell phone, etc., and the sleep state (sd_app_evt_wait()) is canceled?...
Hi,
Can we use BLE 5 beacon with BLE 4 scanner?
As BLE 5 is long range which is my main concern. So, can I get that long range with BLE 4 scanner?
Thanks,
i have done the 10 dfu steps in DFU quick start guide when the boards are not far from each other it works but when i make them far a little
i mean one device in the area...
I am using a Sparkfun nRF52832 breakout. I was trying to install the Softdevice settings onto my Arduino IDE once I clicked on tools -> "nRF5 flash device " the blue ticking...
Current consumption of my code running RTC from LFCLK is ~2.5uA from the power profiler when I set the register values as. NRF_POWER->RAM[2].POWERCLR = 0x01; NRF_POWER->RAM...
Hi,
Currently evaluating SDK and have some issues, I would like to run some demos.
I believe I've managed to erase the "preconfigured" Firmware on the SDK, I have tried...
