Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
Hello,
I'm using "Bluetooth Mesh Light switch" code which i have modified to act as a gateway. Where it periodically collects data from lights. After receiving data from...
Can the VDD PIN of 4L15 be used to detect the ADC voltage? VDD is powered by a dry battery (3.2V~1.8V), LED+ is powered by 3.3V, LED- will be connected to the I/O of the 54L15...
Hi,
I would like to add MCU boot hardware downgrade prevention in my project.
So i had the following config in prj.conf
Then, when i flash my board i get this error...
I am trying to configure himax camera and stream to app but unable to get image, rather when I am using nrf app to see data i am getting data something like this:
'40-13...
I saw a few questions related to this but nothing I found quite answered my question. We are experimenting with the nRF9161 DK, and we need to securely identify which device...
Hi there, right now I'm working with an application that allows me to collect data via UART from several sensors (two), and I also I have a SIM module that allows me to communicate...
Hi,
I'm trying to build the " tx_rx_non_blocking " sample (ncs2.70, nRF52840dk) but get the following error message -
C:/devtools/nordic/ncs/v2.7.0/modules/hal/nordic...
The CPU runs the main thread every 3 seconds, and for the remaining time, it enters the idle thread. However, after entering the idle thread, it doesn’t save power.
But...
Hi guys,
we are planing to use the nRF52820 as BLE proxy to UART/SPI. It shall receive data from a host controller via UART/SPI and forward it via BLE to a smart phone....
I recently purchased an nRF52840 DK (v3.0.0) to use with my custom nRF9160 boards for firmware loading, debugging, and loading certificates for nRF Cloud. While I can successfully...
For connecting an external TCXO reference, we need to know the specification for the slew rate and levels (Vhigh/Vlow). In the product specs, the clock accuracy is defined...
Hello. I'm newbie with the NCS environment so tell me if I'm saying nosense. I use the nrf connect extension in vs code ide. (SDK: v2.7.0 toolchain: v2.7.0)
I want to...
I am working on new project setup. I have copied a sample blinky project from nRF connect SDK(C:\ncs\v2.7.0\zephyr\samples\basic\blinky) and board I selected in Build configuration...
Hi,
I'm following this "Getting started with Nordic's Secure DFU bootloader, a step by step guide" ( https://devzone.nordicsemi.com/guides/short-range-guides/b/software...
