I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Inquiry: NTN Support and Application Feasibility on nRF9151
I would like to seek clarification regarding Non-Terrestrial Network (NTN) support on the nRF9151 .
There have...
Hi there,
When flashing my solution to Lesson 6 Exercise 3 using nrf52DK / nrf52832 - I kept getting an access violation when attempting to setup the timer. I compared the...
Is possible to use ble stack for the configuration and disgnostic of a device and that use ieee802154 to make a start network for 1 to 8 devices , where i can find an examples...
I couldn't find anything related to this issue on the devzone, so I hope this can help someone who has the same issue:
We're using the NRF54L15 QFN52 variant with a custom...
Hello,
Setup
MCU : nRF52840
SDK : nRF5 17.1.0
Transport : Secure Bootloader (UART)
No SoftDevice
Custom HW
The Problem: I am experiencing two conflicting...
I have an application running on a custom board using the nRF52840 that uses the SAADC. After migrating my nRF Connect version from 2.6.2 to 3.1.1 the current draw of my battery...
Hello,
I've been having problems in getting the correct battery voltage for a Thingy53 for a number of projects, when using the latest nRF Connect SDK 3.2.1 (Zephyr 4.2...
I am trying to develop a BLE HID peripheral that can be used on Ubuntu 24.04.
When I try to connect the peripheral_hids_mouse example to a Linux machine, it immediately...
I have two problems. This is the first problem.
[Environ]
nRF Connect SDK v3.2.1 nRF9151 (Custom board) VSCode (1.109.4)
The first problem is that debugging doesn't...
Hello,
You've previously provided the sourcecode for nrfutil, before it was rewritten here https://github.com/NordicSemiconductor/pc-nrfutil .
Is it possible you could...
I am developing a FW for the nrf54l15 which should log sensor data into its internal flash (RRAM) and make it read able later from a Smartphone via BLE.
For this scenario...
Hello everyone,
We hope this message finds you well. We'd really appreciate some guidance on an issue we've been encountering in the field.
We have deployed several hundred...
I am dealing with a HardFault occuring in my code, and I am unable to trace the error. The output when the HardFault occurs is <error> hardfault: HARD FAULT at 0xD0D0D02A...
Hello,
I am using the Nordic Thingy:53 and trying to collect sensor data using Edge Impulse.
I was able to successfully connect the Thingy:53 to Edge Impulse and stream...
The device i am currently developing is a battery powered dongle with internal power supply unit for battery charging. I am using nrf5340 USB pins D+ and D- for communication...
