I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Is there a way of detecting if NFC antenna is connected.
My thought process is, set as GPIOs, one as input and one as output set high to measure the continuity. Am I able...
I believe I'm having a similar issue to this ticket
I'm trying to connect to AWS IoT Core with an nRF7002DK by basing my work on the AWS IoT sample. I'm building the project...
Software version : v4.1.1
Hardware procured in month of June 2024.
Please suggest if any setting needs to be optimised to filter out the inital current.
Load current...
Hi Nordic,
We are planning to port our project from the nRF5 SDK to NCS v2.7.
Currently, we are using NCS v2.7 to build the firmware for our existing custom board based...
Hello,
I'm trying to use a SPIS peripheral from the NRFX library in a nRF Connect SDK 2.7.0 project. The reason for using the NRFX library is to clear a GPIO pin in the...
Hello,
I made a firmware that uses the IPC from the net core to the app core on the nrf700DK board.
I can read the events that generate callback on the receiver core ...
Hi, we are interested in the possibility of using CODED and non-coded (1MB or 2MB) PHYs simultaneously. Our design has an nRF52833 that will be used for connection from a...
Hi,
I need to fully take over the function HardFault_Handler
1. I overwrote the function: HardFault_Handler debug but did not stop in the function HardFault_Handler while...
the on-board J-Link is not showing up on USB anymore besides the FTDI chip still being detected.
So it's not detected anymore by neither JLinkConfig nrfprog or any other...
I'm considering various protocols for mobile robotics applications using Nordic nRF52-based transceivers. The Gazell protocol looks to have a number of appealing features...
What is the exact LFCLK control behavior with regards to control from both the APPCORE and NETCORE? The clock control figure at https://docs.nordicsemi.com/bundle/ps_nrf5340...
We have a custom board in production, which is nRF52832, s132, nrf5 SDK.
Below I provide you some code regarding the peer manager. We use a static key to pair and connect...
I have a program that to fail to start. I read the flash content use jflash, found that the only difference between the program that can run normally is the value on MBR_parameter_addr...
Hi,
This ticket is related to Case ID: 318953.
We have a nRF52820-QDAA-D-R7 on our 6-layer PCB with full ground layer beneath the chip. The chip has the external reset...
Hi,
I am currently developing a project using the nRF52810 as my controller and SEGGER Embedded Studio (version 5.42a) as my IDE. I have successfully integrated the Timer...
