I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
We have a custom board with an nRF5340 connected to a W5500 ethernet interface. The interrupt handler for the W5500 is never executed, despite the interrupt signal being asserted...
Hello, In the DevAcademy lessons I'm currently running blefund_less2_exer1 on the nRF52840 board. Successfully build and flashed firmware using Visual Studio Code enfironment...
Hello, I am trying to find out my nrf 52840 chip revision. I have tried using the NRF_FICR register but I couldn't find the revision there. I found that the variant is AAD0...
Hi
This is a project that reads sensor data and transmits it to the phone. Currently, the sensor data is read and transmitted to the app.
However, if there is 0x00 in...
anyone can tell what is the "Top right-hand side" sector?
Please see below screenshot.
Left hand side is what I dragged and dropped "merged.hex" from \asset_tracker_v2...
I am working on a module MS12SF1(nrf7002+nrf5340). I am using wifi,ble,sdcard,uart and https functionalities in my code. Currently my flash usage is 72.44%. I also want to...
Hello,
I have an aplication that connects to a LTE network and sends periodically a post request with some information to a http server. To get IP server address, I use...
Hi all,
I have an issue with putting my second boot slot on an external SPI flash. There are more people on the Q&A with issues in this realm, but none that I found were...
In our custom board, nrf5340-nrf7002 ,using external RTC ECS-RTC-SOP8-5101A RTC module, which is connected via the I2C bus.
We have configured the RTC's /INT pin (P1.01...
I am using a nrf52840 dongle. I have my own device which has BLE and I am connecting to an app in mobile phone our bluetooth. My goal is to check for the security level what...
Hi , on this code there are not any problems, ,it runs good. but the problem is current.it is 36uA. it is more than ecpectation. because in datasheet.
adxl362 current consumption...
nRF52833 Onboard jlink is broken what to do?
nRF52833 Onboard jlink is broken what to do?
Who can tell me how to make it work, and nRF52833 comes with Debug in and Debug...
Hello, I am using the peripheral_lbs example project and build it for nrf21540dk_nrf21540
I also added CONFIG_SERIAL=n, CONFIG_UART_CONSOLE=n for disabling uart.
But still...
Hi all
I currently have a project where i send and receive commands over UART to another chip. When i receive a message over UART, a callback is triggered and I continuously...
I am having difficulty getting the nrf_regulators_system_off function to work correctly on newer versions of the Connect SDK.
In earlier versions v1.3 and such, the call...
